What to do if my KTM Motorcycle switches off due to low charge?
If your KTM Motorcycle switches off due to a low charge state, you should first charge the KTM PowerPack. If the issue persists, test with a new KTM PowerPack.
What to do if there is a fault during charging my KTM Freeride E-SX?
If you experience a fault during charging of your KTM Motorcycle, stop the charging process, switch off the main switch, and then restart the charging.
What to do if the KTM PowerPack of my KTM Freeride E-SX Motorcycle is too cold?
If the KTM PowerPack is too cold, place it in a warmer location and allow it to warm up. You can also continue charging it in a warmer location.
What to do if my KTM Freeride E-SX charger overheats?
If the charger of your KTM Motorcycle overheats, let it cool down. You can also resume charging in a cooler location.
What to do if there is a fault in the charging cable of my KTM Freeride E-SX Motorcycle?
If you are experiencing a fault in the charging cable of your KTM Motorcycle, check the charging plug and cable for any external damage and reconnect them.
What to do if there is a fault in the KTM PowerPack when connected to the charger of my KTM Freeride E-SX Motorcycle?
If you are experiencing a fault in the KTM PowerPack when connected to the charger, check the charging plug and charging cable for external damage and reconnect.
What to do if there is overtemperature of the control unit of my KTM Motorcycle?
If the control unit of your KTM Motorcycle is overheating, check the coolant level and inspect the radiator for any dirt accumulation.
What to do if there is overtemperature of the motor of my KTM Freeride E-SX?
If the motor of your KTM Motorcycle is overheating, check the coolant level and inspect the radiator for dirt.
What to do if there is overtemperature of the KTM PowerPack of my KTM Motorcycle?
If the KTM PowerPack of your KTM Motorcycle is overheating, allow it to cool down.
What to do if there is a fault in the CAN communication of my KTM Freeride E-SX?
If there is a fault in the CAN communication of your KTM Motorcycle, switch the main switch off and then on again. Also, check that the KTM PowerPack is correctly positioned and ensure the multifunction display connectors are not loose.
General| Battery Capacity | 3.9 kWh |
|---|---|
| Max Torque | 42 Nm |
| Tire Front | 90/90-21 |
| Category | Electric Motorcycle |
| Motor Type | Electric |
| Rated Power | 11 kW |
| Top Speed | 90 km/h |
| Frame Design | Steel |
| Front Suspension | WP XPLOR 43 |
| Rear Suspension | WP XPLOR PDS |
| Front Brake | Hydraulic disc brake, 260 mm |
| Rear Brake | Disc Brake |
| Cooling | Air-cooled |
Specifies the intended purpose and limitations of the vehicle's use.
Outlines risk levels and associated symbols for hazards.
Provides essential guidelines for safe vehicle operation.
Emphasizes the importance of regular service for vehicle longevity.
Explains the purpose and states of the vehicle's main power switch.
Overview of the instrument panel and its display elements.
Covers the speedometer's overview, activation, and messages.
Essential checks before every ride to ensure safety and performance.
Step-by-step guide to starting the motorcycle.
Guidance on proper braking techniques for safe operation.
Details mandatory service tasks based on operating hours.
Adjusting suspension based on rider weight for optimal performance.
Guides for adjusting compression, rebound, and spring preload.
Instructions for adjusting fork compression and rebound damping.
Procedure for topping up the front brake fluid reservoir.
How to replace blown fuses for various vehicle components.
Steps for safely detaching the high-voltage battery from the vehicle.
Detailed procedure for charging the high-voltage battery.
Lists common vehicle faults, their causes, and actions to resolve them.
To Next Page