LeCroy WAVESURFER

To Next Page

To Previous Page

WaveSurfer DSO

WS-OM-E Rev B 85

100BASE-T ETHERNET CONNECTION

Connecting to a Network

Use the Ethernet connector (item 2 in the I/O panel diagram) to connect the instrument to a

network:

Communicating over the Network

The instrument uses Dynamic Host Configuration Protocol (DHCP) as its addressing protocol.

Therefore, there is no factory set IP address.

Main Page

Default Chapter6
- Table of Contents6
How to Use On-Line Help13
- Type Styles13
- Instrument Help13
- Windows Help14
Returning a Product for Service or Repair14
Technical Support14
Staying Up-To-Date14
Warranty15
Copyright15
- Windows License Agreement16
- End-User License Agreement for Lecroy® X-Stream Software16
Virus Protection23
Specifications23
- Vertical System23
- Horizontal System24
- Acquisition System24
- Acquisition Processing24
- Triggering System25
- Basic Triggers25
- SMART Triggers -- Standard25
- SMART Triggers -- Optional26
- Automatic Setup26
- Documentation and Connectivity26
- Probing27
- Color Waveform Display27
- Analog Persistence Display27
- Zoom Expansion Traces27
- Rapid Signal Processing28
- Internal Waveform Memory28
- Setup Storage28
- Auxiliary Output28
- Auxiliary Input28
- Math Tools (Standard)28
- Extended Math (Mathsurfer Option)28
- Measure Tools (Standard)28
- Pass/Fail Testing29
- General29
- Warranty and Service29
- Environmental Characteristics30
  - Temperature30
  - Humidity30
  - Altitude30
  - Random Vibration30
  - Shock30
- Certifications30
  - CE Declaration of Conformity30
Safety Requirements31
- Safety Symbols and Terms31
- Operating Environment32
- Cooling Requirements33
- AC Power Source33
- Power and Ground Connections34
- On/Standby Switch34
- Calibration35
- Cleaning35
- Abnormal Conditions35
Basic Controls35
- Front Panel Controls35
- On-Screen Toolbars, Icons, and Dialog Boxes39
  - Menu Bar Buttons39
  - Dialog Boxes40
- Alternate Access Methods40
  - Mouse and Keyboard Operation40
  - Tool Bar Buttons40
- Trace Descriptors41
- Trace Annotation42
  - To Annotate a Waveform42
- To Turn on a Trace43
- Screen Layout44
Installation45
- Hardware Installation45
  - Instrument I/O Panel45
- Software45
  - Checking the Scope Status45
- Default Settings46
  - Wavemaster and Wavepro 7000 Series Dsos46
- DDA, SDA, and Waverunner Dsos46
- Adding a New Option47
- Restoring Software48
  - Restarting the Application48
  - Restarting the Operating System48
Connecting to a Signal48
- Probus Interface48
- Auxiliary Output Signals49
- To Set up Auxiliary Output49
Sampling Modes49
- To Select a Sampling Mode49
- Single-Shot Sampling Mode50
  - Basic Capture Technique50
- RIS Sampling Mode -- for Higher Sample Rates50
- Roll Mode51
Vertical Settings and Channel Controls52
- Adjusting Sensitivity and Position52
  - To Adjust Sensitivity52
  - To Adjust the Waveform's Position52
- Coupling52
  - Overload Protection52
  - To Set Coupling52
- Probe Attenuation53
  - To Set Probe Attenuation53
- Bandwidth Limit53
  - To Set Bandwidth Limiting53
- Quickzoom53
  - To Turn on a Zoom53
- Finding Scale54
  - To Use Find Scale54
- Variable Gain54
  - To Enable Variable Gain54
- Channel Deskew54
  - To Set up Channel Deskew54
Timebase and Acquisition System54
- Timebase Setup and Control54
- Dual Channel Acquisition55
  - Combining of Channels55
- Autosetup55
Triggering55
- Simple Triggers55
- SMART Triggers59
Display Formats76
- Display Setup76
- Persistence Setup77
- Screen Saver79
- Zooming Waveforms79
- To Zoom a Single Waveform80
- To Zoom by Touch-And-Drag81
- To Zoom Multiple Waveforms Quickly81
- To Turn off Zoom81
- XY Display82
  - To Set up XY Displays82
Save and Recall83
- Saving and Recalling Scope Settings83
- Saving Screen Images84
- Saving and Recalling Waveforms85
  - Saving Waveforms85
  - Recalling Waveforms86
- Disk Utilities87
Printing and File Management88
- Printing88
- Managing Files89
  - Hard Disk Partitions89
100Base-T Ethernet Connection90
- Connecting to a Network90
- Communicating over the Network90
  - Windows Setups91
  - System Restore91
Waveform Measurements92
- Measuring with Cursors92
- Cursors Setup92
  - Quick Display92
- Full Setup93
- Overview of Parameters93
- Statistics96
- Measure Gate97
  - To Set up Measure Gate98
- To Select a Parameter98
- Parameter Calculations99
- List of Parameters103
Waveform Math109
- Introduction to Math Traces and Functions109
- Fft111
- Improving Dynamic Range114
- Record Length114
  - FFT Algorithms114
  - Glossary116
- FFT Setup119
  - To Set up an FFT119
Analysis119
- Pass/Fail Testing119
Utilities122
- Status122
  - To Access Status Dialog122
- Remote Communication122
  - To Set up Remote Communication122
  - To Configure the Remote Control Assistant Event Log122
- Hardcopy123
- Aux Output124
- Date & Time124
- Options126
- Preferences126
- Offset Control126
  - Delay Control127
  - E-Mail127
- Acquisition Status128
- Service128
- Show Windows Desktop128
- Touch Screen Calibration128

Table of Contents

Related product manuals