Lenze E82EV751K4C User Manual

Total index
2
Guide
2.3
L
2.3-3
EDS82EV903-1.0-11/2002
Configuration
- Acceleration times and deceleration times, 10.7-1
- Actual value selection, 10.8-1
- Analog input signals, 10.12-1
- Analog output signals, 10.12-4
- Analog outputs, 10.12-4
- Analog process data output words, 10.12-10
- Change of direction of rotation, 10.7-5
- Chopper frequency of inverter, 10.4-3
- Code table, 10.20-1
- Communication monitoring, 10.20-14
- Controller inhibit (DCTRL1-CINH), 10.5-3
- Current limits, 10.6-3
- Current-limit controller, 10.11-1
- DC-injection brake (DCB), 10.7-6
- Digital input signals, 10.13-1
- Digital output signals, 10.13-6
- Digital outputs, 10.13-6
- Display functions, 10.16-1
- Function library, 10.1-1
- Manual / remote operation, 10.8-17
- Maximum field frequency, 10.6-1
- Minimum field frequency, 10.6-1
- Monitoring functions
external faults, 10.15-1
Motor temperature, 10.14-1
- Motor data detection, 10.9-1
- Oscillation damping, 10.4-4
- Parameter set changeover, 10.17-5
- Process data output words, 10.13-12
- Quick stop (QSP), 10.7-4
- Relay output, 10.13-6
- Setpoint selection, 10.8-1
- Setpoint source selection, 10.8-1
- Slip compensation, 10.4-1
- Speed limit values, 10.6-1
- Start conditions/flying-restart circuit, 10.5-1
- Thermal motor monitoring, 10.14-1
- TRIP reset, 10.15-1
- TRIP set, 10.15-1
- V/f rated frequency, 10.3-5
- Vmin boost, 10.3-7
Conformity, 1.4-1, 4.2-1
Control characteristics, Process controller, 10.10-1
Control connections
- Terminal assignment - application I/O, 7.2-9, 7.3-9,
7.4-9
- Terminal assignment - standard I/O, 7.2-4, 7.3-4,
7.4-4
- Terminal assignment - standard I/O PT, 7.2-8, 7.2-13,
7.3-8, 7.3-13, 7.4-8, 7.4-13
Control word, 10.20-15
Controlled deceleration after mains failure, 10.5-4
Controller
- Application as directed, 1.4-1
- Labelling, 1.4-1
Controller inhibit, Drive performance, 10.5-1, 10.5-3
Controller protection, 3.4-1
Controlling the brake
- Parameter setting of the relay output, 13.3-2
- Via the relay output, 13.3-2
Copying parameter sets
- E82ZBC keypad, 9.3-6
- XT EMZ9371BC keypad, 9.4-6
Copying parameters, to other controllers
- E82ZBC keypad, 9.3-6
- XT EMZ9371BC keypad, 9.4-6
Current limits, 10.6-3
Current-limit controller, 10.11-1
D
Dancer position control, 15.4-1
Data, Keypad E82ZBC, 9.3-1
DC bus, Cable cross-section, 12.4-4
DC group drives, 4.2-1
DC-bus connection
- Braking in, 12.8-1
- Central supply, 12.6-1
- Central supply via external DC source, 12.6-1
- Central supply via regenerative power supply module,
12.6-2
- DC-bus connection, 12.4-4
- Decentralised supply, 12.7-1
- Decentralised supply with single-phase or two-phase
mains connection, 12.7-1
- Decentralised supply with three-phase mains
connection, 12.7-2
- Mains connection, 12.4-2
- Possible combinations, 12.4-1
- Protection concept, 12.4-8
- Required mains filters/mains chokes, 12.5-2
DC-bus fuse, 12.4-5
DC-injection brake, 10.7-6
Dead band
- Settings with auto DCB, 10.7-8
- With analog setpoint selection, 10.8-5
Debouncing
- Digital output signal ”Torque threshold reached”,
10.20-22
- Digital output signal PCTRL1-LIM, 10.20-20
- Digital output signal PCTRL1-SET=ACT, 10.20-20
- Digital outputs, 10.13-9, 10.20-41
Deceleration, 10.7-1
Show/Hide Bookmarks

Lenze E82EV751K4C Specifications

General

Brand	Lenze
Model	E82EV751K4C
Category	DC Drives
Language	English