List of illustrations
2
Guide
2.4
L
2.4-4
EDS82EV903-1.0-11/2002
Fig. 8.3-1 Comparison of V/f characteristic control and vector control 8.3-1....................
Fig. 9.3-1 Installation and commissioning of the E82ZBC keypad or
E82ZBB diagnosis terminal 9.3-2............................................
Fig. 9.3-2 Display elements and function keys of the E82ZBC keypad 9.3-3....................
Fig. 9.4-1 Installation and commissioning of XT EMZ9371BC keypad or
E82ZBBXC diagnosis terminal 9.4-2..........................................
Fig. 9.4-2 Display elements and function keys of the XT EMZ9371BC keypad 9.4-2..............
Fig. 10.3-1 Comparison of V/f characteristic control and vector control 10.3-1....................
Fig. 10.3-2 Linear and square-low V/f characteristic 10.3-3..................................
Fig. 10.3-3 Umin boost at linear and square-law V/f characteristic 10.3-7.......................
Fig. 10.4-1 Effect of the skip frequencies 10.4-7..........................................
Fig. 10.6-1 Relation between setpoint and minimum and maximum output frequency 10.6-1.........
Fig. 10.7-1 Acceleration times and deceleration times for linear ramp function generator 10.7-2.......
Fig. 10.7-2 Acceleration times and deceleration times for linear ramp function generator 10.7-3.......
Fig. 10.8-1 Gain and offset at unipolar setpoint selection 10.8-6..............................
Fig. 10.8-2 Gain and offset at bipolar setpoint selection 10.8-6...............................
Fig. 10.8-3 Gain and offset at inverse setpoint selection 10.8-7...............................
Fig. 10.8-4 Calculation example for gain and offset 10.8-7..................................
Fig. 10.8-5 Motor potentiometer with NC contacts 10.8-12...................................
Fig. 10.10-1 Example: Dancer control with adding influence of the process controller 10.10-3..........
Fig. 10.10-2 Example: Dancer control with subtractive influence of the process controller 10.10-4.......
Fig. 10.12-1 Output signal of the function ”1/output frequency” 10.12-9..........................
Fig. 10.14-1 Tripping characteristic of I2t monitoring 10.14-2..................................
Fig. 12.4-1 Decentralised switching of the mains supply in network operation 12.4-3...............
Fig. 12.4-2 Example: DC connection of three controllers 12.4-4...............................
Fig. 12.5-1 Example with two simultaneously accelerated and decelerated drives 12.5-9............
Fig. 12.5-2 Example with two not simulateneously accelerated or decelerated drives 12.5-9..........
Fig. 12.6-1 Network of 230 V controllers with central supply via external DC source 12.6-1..........
Fig. 12.6-2 Network of 400 V controllers with central supply
via 934X regenerative power supply unit 12.6-2..................................
Fig. 12.7-1 Network of 230 V controllers with decentralised supply
with single or two-phase mains connection 12.7-1...............................
Fig. 12.7-2 Network of three-phase connected controllers
with decentralised supply and additional braking unit 12.7-2........................
Fig. 13.4-1 Wiring of brake transistor with 8200 vector 0.25 ... 11 kW 13.4-11.....................
Fig. 13.4-2 Connection of the brake resistor to 8200 vector 15 ... 90 kW 13.4-11...................
To Next Page
Loading...
Need help?
General