Lonking CDM853 - Page 90

To Next Page

To Previous Page

WARNING:

WARNING: If

If the

the

the loader

loader

loader moves,

moves,

moves, immediately

immediately

immediately step

step

step down

down

down the

the

the service

service

service brake

brake

brake pedal

pedal

pedal ,

rotate

rotate the

the

the hand

hand

hand brake

brake

brake button

button

button to

to reset

reset

and

and apply

apply

apply the

the

the braking.

braking.

braking. Thereafter,

Thereafter,

inspect

inspect whether

whether

whether there

there

there is

is any

any

any fault

fault

fault with

with

with the

the

the gear-shifting

gear-shifting

gear-shifting control

control

control system.

system.

system. If

If the

the

loader

loader is

is on

on a

a slope,

slope,

slope, be

be sure

sure

sure to

to block

block

block up

up all

all

all wheels

wheels

wheels with

with

with chocks

chocks

chocks so

so as

as to

prevent

prevent the

the

the loader

loader

loader from

from

from moving,

moving,

moving, and

and

and then

then

then operate

operate

operate the

the

the loader.

loader.

NOTE:

NOTE: When

When

When carrying

carrying

carrying out

out

out gear-shifting

gear-shifting

gear-shifting operation,

operation,

operation, release

release

release the

the

the accelerator

accelerator

accelerator pedal

pedal

firstly

firstly and

and

and then

then

then operate

operate

operate the

the

the gear-shifting

gear-shifting

gear-shifting lever

lever

lever for

for

for realizing

realizing

realizing the

the

the gear

gear

gear shifting,

shifting,

shifting, so

as to

to protect

protect

protect the

the

the gear-shifting

gear-shifting

gear-shifting clutch.

clutch.

5. Inspect the performance of service brake. On a flat and open ground, drive the loader

with forward gear 1 or forward gear 2 engaged, release the accelerator pedal, and

the same time smoothly push down brake pedal. The loader shall slow down

obviously a nd then stop.

NOTE:

NOTE: If

If you

you

you cannot

cannot

cannot feel

feel

feel that

that

that the

the

the loader

loader

loader slows

slows

slows down

down

down obviously

obviously

obviously after

after

after the

the

the brake

brake

pedal

pedal is

is stepped

stepped

stepped down,

down,

down, please

please

please immediately

immediately

immediately rotate

rotate

rotate the

the

the red

red

red button

button

button of

of parking

parking

brake

brake so

so as

as to

to reset

reset

and

and apply

apply

apply the

the

the emergency

emergency

emergency braking.

braking.

braking. At

At the

the

the same

same

same time,

time,

time, by

operating

operating the

the

the pilot

pilot

pilot joys

joys

joys tick,

tick,

tick, lower

lower

lower the

the

the lift

lift

lift arm

arm

arm to

to the

the

the lowest

lowest

lowest position,

position,

position, tilt

tilt

forwards

forwards the

the

the bucket,

bucket,

bucket, and

and

and insert

insert

insert the

the

the bucket

bucket

bucket teeth

teeth

teeth into

into

into or

or push

push

push against

against

against the

the

ground,

ground, so

so as

as to

to stop

stop

stop the

the

the loader

loader

loader and

and

and ensure

ensure

ensure the

the

the safety.

safety.

2. Step down the service brake pedal, rotate the

handle brake button to reset it, slowly let go

of the service brake pedal, and observe

whether the loader moves.

3 . Push the control handle so as to get the

forward gear 1 engaged or pull the gear-

shifting lever backwards so as to get the

reverse gear 1 engaged, and at the same

time push down the accelerator pedal

appropriately. In this way, the loader will

travel forw ards or backwards.

4. Inspect the engagement of each gear. Drive

the loader to a flat and open ground, get

each gear engaged respectively, and inspect

the gear-shifting operation. If in the operation

of the previous phase, the inspection on

steering performance was not carried out

owing to the small place, please turn the

steering wheel now, and inspect whether the

loader can turn left or right.

Main Page

Lonking CDM853 - Page 90

Table of Contents