EasyManua.ls Logo

Lonking CDM853 - Page 91

Lonking CDM853
153 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
90
The loader is equipped with the articulated-type fully-hydraulic coaxial-flow-
amplifying powered steering gear, and the turning angle of the steering wheel is not
equal to the turning angle of the loader. When the steering wheel is turned
continuously, th e turning angle of the loader will increase until the intended angle is
obtained. The turning speed of the loader will increase as the turning speed of the
steering wheel increases.
After being turned, the steering wheel will not return to the original position
automatically, and the turning angle of the loader will remain unchanged. Therefore,
after the turning of the loader is completed, be sure to turn the steering wheel in
opposi te direction so as to eliminate the relative angle between front and rear frames
and make the loader run straightly. After the turning operation is completed, pull the
turn lamp switch to the middle position, so as to turn off the turn lamps and turn
indi cating lamp.
For the purpose of carrying out the turning operation when the loader is travelling
at
high speed, be sure to release the accelerator pedal firstly. If necessary, apply the
service brake to slow down the loader and then carry out the turning operation, so as
to ensure the safety.
WARNING:
WARNING:
WARNING:
WARNING: Do
Do
Do
Do not
not
not
not carry
carry
carry
carry out
out
out
out turning
turning
turning
turning operation
operation
operation
operation on
on
on
on a
a
a
a slope.
slope.
slope.
slope. The
The
The
The turning
turning
turning
turning
operation
operation
operation
operation may
may
may
may be
be
be
be completed
completed
completed
completed only
only
only
only after
after
after
after the
the
the
the loader
loader
loader
loader has
has
has
has been
been
been
been driven
driven
driven
driven to
to
to
to the
the
the
the flat
flat
flat
flat
ground.
ground.
ground.
ground.
7. For the purpose of braking the loader, just release the accelerator pedal, and then
smoothly push down the brake pedal.
WARNING:
WARNING:
WARNING:
WARNING: When
When
When
When the
the
the
the loader
loader
loader
loader is
is
is
is running
running
running
running at
at
at
at high
high
high
high speed,
speed,
speed,
speed, unless
unless
unless
unless any
any
any
any emergency
emergency
emergency
emergency
circumstance
circumstance
circumstance
circumstance occurs,
occurs,
occurs,
occurs, be
be
be
be sure
sure
sure
sure not
not
not
not to
to
to
to push
push
push
push down
down
down
down the
the
the
the brake
brake
brake
brake pedal
pedal
pedal
pedal to
to
to
to the
the
the
the end
end
end
end
violently,
violently,
violently,
violently, otherwise
otherwise
otherwise
otherwise the
the
the
the emergency
emergency
emergency
emergency braking
braking
braking
braking may
may
may
may cause
cause
cause
cause safety
safety
safety
safety accident
accident
accident
accident or
or
or
or
damage
damage
damage
damage the
the
the
the loader.
loader.
loader.
loader.
6. In case there is a corner ahead, please
operate the loader in accordance with the
local laws and regulations relating to traffic.
When the loader is about to turn, pull or push
the turn lamp handle in the corresponding
direction. As indicated in the figur e below,
push forwards the handle if the loader will
turn left, and pull backwards the handle if the
loader will turn right. Now the front/rear turn
lamps on one side of the loader and the
corresponding turn indicating lamp on the
instrument board will co me on, so
as
to warn
the loaders and persons around the loader
that this loader
is
about to turn. Thereafter,
turn the steering wheel in the turning
direction, so
as
to make the loader to turn.

Table of Contents