Why is my Maytag MDB Dishwasher not drying properly?
If your Maytag dishwasher isn't drying dishes well, it could be due to several reasons. Make sure you're using rinse aid and that the dispenser isn't empty. Check the rinse aid gauge level and refill if necessary. Consider using the heated dry or smart dry option. For other potential causes, please refer to the service error codes table.
Why is the Sanitized LED blinking on my Maytag MDB?
If the Sanitized LED is blinking or you're seeing an incomplete sanitization message on your Maytag dishwasher, it means the control couldn't confirm sanitization. This can occur if the door was opened during the final rinse or dry cycle, so avoid opening the door during these phases. Also, ensure the incoming water is at least 84°F (29°C); run the water at the sink until it reaches 120°F (49°C) before starting the dishwasher. Check the power source and confirm at least 100 VAC. For heating or sensor-related issues, refer to the service error codes table.
Why is detergent left in the dispenser of my Maytag MDB?
If detergent isn't dispensing properly or is left in the dispenser of your Maytag dishwasher, ensure that items in the lower rack aren't blocking the lid or the spray of water to the dispenser. Avoid overfilling the dispenser to prevent the lid latch from binding. If these steps don't resolve the issue, unplug the dishwasher and check or replace the dispenser. For dispenser electrical problems or other error-related issues, refer to the service error codes table.
General| Type | Built-In |
|---|---|
| Capacity | 14 Place Settings |
| Tub Material | Stainless Steel |
| Energy Star Certified | Yes |
| Soil Sensor | Yes |
| Heated Dry | Yes |
| Control Type | Electronic |
| Delay Start | Yes |
Provides service information for the Maytag Chopper Dishwasher.
Outline the aims of the service manual for In-Home Service Professionals.
Crucial safety messages and alert symbols for potential hazards.
Explains the Maytag Chopper Wash System and how it disintegrates food.
Details new components like chopper sump, console display, and stainless steel elements.
Locating the model/serial number label and tech sheet.
Explains the structure of model and serial numbers for identification.
Provides key technical specifications for the dishwasher.
Identifies various parts and features within the dishwasher.
Blank page for notes.
Safety precautions for technicians, including electrical hazards and ESD.
Details the service diagnostic cycle intervals and LED indicators.
Instructions on invoking and using the service diagnostic cycle.
Guidance on advancing through customer cycles for testing.
Procedure for displaying and interpreting error codes.
Table listing function codes, problem codes, causes, and checks.
Guides for diagnosing common customer-reported issues.
Safety precautions for performing tests on the appliance.
Schematic showing electrical connections and components.
Specifications and component testing guidelines for the control board.
Procedure to verify incoming and outgoing power to the control board.
Tests for the door switch and its wiring for proper operation.
Tests for the fill valve, float switch, and associated wiring.
Checks the dispenser solenoid or wax motor and its wiring.
Tests the heater element, hi-limit thermostat, and heating circuit.
Tests the OWI sensor, thermistor, and related wiring.
Tests the wash/rinse motor, capacitor, and electrical connections.
Tests the drain motor and its associated wiring and connections.
Tests the vent wax motor and its electrical connections.
Tests the vent fan motor and its DC voltage supply.
Tests the AC fan motor and its electrical connections.
Tests the Power Blast wax motor and its AC voltage supply.
Tests the UI connection to the control board and its functionality.
Procedure for adjusting door spring tension.
Instructions for installing insulation and removing the door latch strike.
Steps to access door components and the user interface.
Step-by-step guide to remove the door latch assembly.
Procedure for removing the electronic control board.
Instructions for removing the detergent dispenser assembly.
Steps to remove water inlet and drain hoses and fill valve.
Accessing and disassembling Power Dry™ components.
Accessing and identifying components of the overfill assembly.
Identification of components located inside the dishwasher tub.
Identification of spray arms, feed tube, and manifold.
Instructions for removing the upper rack and culinary tool rack.
Procedure for removing and reinstalling the lower spray arm.
Identification of components located under the dishwasher tub.
Steps to remove the heater element and associated parts.
Procedure for removing the drain pump from the sump.
Instructions for accessing and removing the OWI sensor.
Preparation and steps for removing the sump assembly.
Exploded view and parts list for the chopper motor assembly.
Step-by-step guide to remove the chopper motor assembly.
To Next Page
