To Next PageTo Next Page
Need help?Do you have a question about the MCS MCS-DOOR-KEYPAD and is the answer not in the manual?
Describes the 6-wire shielded cable for keypad and display connection.
Details the MCS-MAGNUM-DOOR keypad/display features and specifications.
Details the MCS-MAGNUM-OEM keypad/display features and specifications.
Lists features of the Door Mount Package for Magnum Keypad/Display.
Lists features of the OEM Mount Package for Magnum Keypad/Display.
Explains how to navigate and use the main menu screens with function keys.
Displays chiller status, system status, mode, time, and target values.
Shows chiller status, unit status, time, current amps, KW, and tons.
Displays compressor 1 status including PSI, temperature, and motor information.
Shows compressor 1 superheat data, including SST, SSH, SCT, and DSH.
Details compressor 1 EXV or LLS status, valve position, and slope.
Displays compressor 2 status including PSI, temperature, and motor information.
Shows compressor 2 superheat data, including SST, SSH, SCT, and DSH.
Details compressor 2 EXV or LLS status, valve position, and slope.
Shows the current status (On/Off) of up to four relays.
Displays the last 'On' time for up to four relays.
Shows the last 'Off' time for up to four relays.
Displays the run time today (TDY) for up to four relays.
Shows the number of cycles today (TDY) for up to four relays.
Displays run time yesterday (YDY) for up to four relays.
Shows cycles yesterday (YDY) for up to four relays.
Displays total run hours (TTL Run HR) for up to four relays.
Shows total cycles (TTL Cycles) for up to four relays.
Displays the status of up to four analog outputs.
Shows the maximum value today (Max TDY) for up to four analog outputs.
Displays the minimum value today (Min TDY) for up to four analog outputs.
Shows the average value yesterday (Avg YDY) for up to four analog outputs.
Displays the maximum value yesterday (Max YDY) for up to four analog outputs.
Shows the minimum value yesterday (Min YDY) for up to four analog outputs.
Displays the average value yesterday (Avg YDY) for up to four analog outputs.
Displays the current value for up to four sensor inputs.
Shows the type of up to four sensor inputs.
Displays the last 'On' time for up to four sensor inputs.
Shows the last 'Off' time for up to four sensor inputs.
Displays the maximum value today (Max TDY) for up to four sensor inputs.
Shows the minimum value today (Min TDY) for up to four sensor inputs.
Displays run hours today (Run TDY) for up to four sensor inputs.
Shows the average value today (Avg TDY) for up to four sensor inputs.
Displays cycles today (Cycles TDY) for up to four sensor inputs.
Shows run hours yesterday (Run YDY) for up to four sensor inputs.
Displays the maximum value yesterday (Max YDY) for up to four sensor inputs.
Shows cycles yesterday (Cycles YDY) for up to four sensor inputs.
Displays the minimum value yesterday (Min YDY) for up to four sensor inputs.
Shows total run hours (TTL Run HR) for up to four sensor inputs.
Displays the average value for yesterday (Avg YDY) for up to four sensor inputs.
Shows total cycles (TTL Cycles) for up to four sensor inputs.
Displays current alarms, including status and time.
Displays graphs for relays or sensors, allowing sample time editing.
Allows editing the sample rate for graphs and navigating through selections.
Displays setpoints and their corresponding values, based on authorization level.
Configures RS485 protocol, address, and baud rate.
Lists options under Service Tools, including RS485 Network and Ethernet Network.
Lists options under Service Tools, focusing on Ethernet Network settings.
Configures Ethernet dynamic IP and IP address.
Sets the Subnet Mask and Default Gateway for Ethernet.
Configures the MCS Port for Ethernet setup.
Displays system information, including RS485, Ethernet, Time/Date, and Display settings.
Shows system firmware version and configuration name.
Displays company name and model number.
Shows the unit serial number and installation date.
Displays the configuration version and date.
Shows bootloader version and hardware serial number.
Displays physical MAC address and I/O board type.
Accesses system time and date settings.
Allows setting the system time and date.
Prompts to save or discard changes to time and date settings.
Accesses display settings for contrast and background.
Adjusts display contrast and reverses background.
Reverses the display background from light to dark.
Clears the historical alarm log.
Confirms clearing of alarm history.
Accesses the option to clear point information.
Confirms clearing of point information.
Indicates changes require higher authorization.
Accesses sensor diagnostic tools.
Displays diagnostic results for Sensor M-1.
Accesses configuration checksums.
Displays checksum values for configuration items.
Accesses the operating schedule settings.
Sets the operating schedule for Sunday.
Configures operating schedule times and settings.
Accesses holiday date settings.
Allows setup of holiday dates.
Accesses BACnet settings.
Configures BACnet Device ID and TCP/IP Port.
Sets the BACnet Device ID number.
Sets the BACnet TCP/IP port number.
Resets lockouts on the system, with a daily limit.
Explains the format for entering passwords and password levels.
Shows how entered characters are displayed and keypad limitations.
Displays the authorization level after password entry.
General