5-2
Specifications of the main unit
Item CG-60SRIII CG-100SRIII CG-130SRIII
Acceptable sheet width
mm inch mm inch mm inch
90~740 4~28 90~1250 4~48 90~1550 4~60
Acceptable
roll sheet
Outside
diameter
150mm or less 200mm or less, Sheet
Sheet weight 8 kg or less 20 kg or less
Effective cutting area
*1
*1. The maximum feed length is limited by the software.
The maximum feed length is limited also by the sheet setting condition or by the effect of obstacles encountered on the sheet
path. As a rule of thumb, limit the maximum feed length for one of the data to 2 m.
606 mm X 51 m 1070 mm X 51 m 1370 X 51m
Maximum
speed
Shaft direction 70 cm/s
45° direction 100 cm/s
Speed setting
(cutting/plotting)
1 ~ 10cm/s (in 1 cm/s steps)
10 ~ 70cm/s (in 5 cm/s steps)
Mechanical resolution X: 2.5μm, Y: 5μm
Program steps
25, 10μm (MGL-IIc)
100, 50,μm( MGL-Ic1)
Repeatability
*2
*2. To achieve the guaranteed range of accuracy, the next page's requirements must be satisfied.
0.2 mm / 2m (excluding expansion/contraction due to film temperatures)
Guaranteed range of accuracy
(repeatability)
606 mm X 2 m 1070 mm X 2 m 1370 X 2m
(depending on the specified film and cutting conditions)
Maximum pressure 500 g
Pressure
setting
Cutter
10 ~ 20g(2 g step)
20 ~ 100g(5 g step)
100 ~ 500g(10 g step)
Pen
10 ~ 20g(2 g step)
20 ~ 100g(5 g step)
100 ~ 150g(10 g step)
Acceptable films
PVC sheets (0.25 mm thick or less,
included laminated sheet),
fluorescent sheets
*3
, reflective sheets
*4
, rubber sheet
*3. The blade (SPB-0007) dedicated for fluorescent sheets or the blade (SPB-0006) dedicated for reflective sheets must be used.
Applicable tools
Eccentric cutters, water-based ball-point pens, oil-based ball-point pens,
commercially available ball-point pens
*4
*4. Use the tools supplied as standard accessories.
If any other ball-point pen available on the market is to be used, select the one whose diameter is 8 to 9 mm and which is free
from bumps or taper in the area to be clamped. The image quality is not guaranteed because the pen tip position differs
depending on the pen in use.
Commands
*5
*5. With the USB connection, the ESC type commands among the MGL-llc commands cannot be used.
MGL-IIc, MGL-Ic1
Interface USB, RS-232C, Ethernet
Receiver buffer
Approximately 27 MB standard (Approximately17MB when the sorting function
is effective.)
Operating environment 5 to 35°C, 35 to 75 % (Rh) Non-condensing
Power capacity
AC100 to AC240 V
140 VA to 168VA
AC100 to AC240 V
190 VA to 228VA
Outside
dimensions
(W)
1030 mm 1530 mm 1830 mm
(D)
287 mm 580 mm
(H)
335 mm 1150 mm
Weight
24 kg 41 kg 46 kg
Noise
*6
*6. The values are based on MIMAKI's measurement conditions.
During standby (plotting)50 dB (Absorption fan at low speed)
During cutting (plotting)70 dB (Continuous sounds)
To Next Page
Loading...
