Mircom flexnet - Page 24

To Next Page

To Previous Page

Mechanical Installation and Dimensions

Figure 7: Chassis Installation into BBX-1072A

Mount chassis FX-2017-12N into backbox BBX-1072A using the supplied hexnuts as shown below.

2012

Main Page

Table of Contents3
Introduction5
Additional Features7
Document Conventions7
System Components10
Mechanical Installation and Dimensions18
Chassis Installation23
Module Mounting Locations26
Display and Adder Modules Mounting Locations28
Module Settings31
Basic Mode41
Field Wiring48
- Main Fire Alarm Module Terminal Connections48
- Analog Loop Wiring50
- FNC-2000 Fire Network Controller Module56
- FOM-2000-SP Fiber Optic Network Adder Module57
- Detection Module (DM-1008A) Terminal Connections58
- Signal Module (SGM-1004A) Terminal Connections59
- Relay Module (RM-1008(A)) Terminal Connections60
- Polarity Reversal and City Tie Module (PR-300) Wiring61
- UDACT-300A Main Board Terminal Connections62
- Power Supply Connections63
- Wiring Tables and Information64
System Checkout66
Indicators, Controls, and Operation67
- Common Indicators68
- Common Controls69
- Single Stage Operation71
- Two Stage Operation71
- Pre-Signal Operation72
- Circuit Types73
Configuration76
- Configuration Backup, Query and Fast-Forward76
- OPEN Graphic Navigator Software Package76
- Ethernet Port76
- Boolean Logic Engine76
- Uboot Based Bootloader76
Typical Flex-Nettm System Layouts with Audio77
System Components for the Integrated Fire/Audio Cabinet79
- Network Fire Alarm79
- Network Controller Modules79
- Fiber Optics Module80
- Adder Modules80
- Auxiliary Modules80
- Programmable Modules80
Flexnettm Mass Notification System (BBX-FXMNS) Enclosure81
Integrated Fire/Audio Cabinet Mechanical Installation85
Mechanical Installation for the Expansion Audio Cabinet87
Integrated Fire/Audio Cabinet - Audio Module Placement and Internal Wiring89
Integrated Fire Alarm Connection90
- Battery Power90
- Transformer Power90
QBB-5001/R Expansion Audio Cabinet Module Placement91
- QPS-5000N Power Supply Connection92
Installing and Removing Amplifiers92
Multiple QBB-5001/R Cabinet Connections93
Audio Network Card and Telephone Network Card94
Audio Amplifier Wiring95
- QAA-5230-70/25 Amplifier Wiring95
- QAA-5230S-70/25 Amplifier Wiring96
- QAA-5415-70 and QAA-5415-25 Amplifier Wiring97
- Qaa-5160-70/25101
- Backup Amplifier103
Displays & Controls104
Setup105
- QBB-5001/R Amplifier Installation105
- Before Turning the Power "ON105
Audio Configuration105
Lobby Enclosures106
ANC-5000 Audio Network Controller Module107
ANC-5000 Wiring108
QMP-5101NV Vertical Paging Control Module110
Paging Modules111
- QMP-5101N Network Master Paging Control Module111
QMP-5101N/V Network Paging Wiring113
Paging Operation114
TNC-5000 Telephone Network Controller Module116
TNC-5000 Telephone Wiring120
QMT-5302NV Vertical Master Telephone122
QMT-5302N Master Firefighters' Telephone123
QMT-5302N Connections124
QAZT-5302/DS Network Firefighters' Telephone Selector Panel125
Telephone Operation127
Appendix A: Specifications128
- Compliance129
- ULI/ULC Integrated Fire Alarm and Audio Panel Specifications130
Appendix B: Power Supply and Battery Calculations132
- Raxn-Lcd/Raxn-Lcdg133
Appendix C: DIP Switch Settings134
- ANC-5000 Board with Ethernet Port, Address Setting (DIP SWITCH SW1)135
- ANC-5000 Board Without Ethernet Port, Address Setting (DIP SWITCH SW1)135
- ACN-792M Loop Adder Module (CPU) Address Setting (DIP SWITCH SW1)135
- RAXN-LCD/RAXN-LCDG Remote Annunciator Address Setting (DIP SWITCH SW1)135
Appendix D: Alarm Verification Timing135
Appendix E: Wiring for Addressable Supervised Output Module136
Appendix F: ULC Compatible Speakers137
Appendix G: ULI Compatible Speakers138
Appendix H: Power Supply & Batteries for Audio139
Appendix I - POWER-LIMITED WIRING SCHEME140
Appendix J FXMNS Used as a Mass Notification System (ACU)141
Warning Please Read Carefully146
Warranty & Warning Information146
- Limited Warranty148
- Out of Warranty Repairs149

Mircom flexnet - Page 24

Table of Contents

Related product manuals