Ness D8 Installation & Programming Manual

12
PROGRAMMING
NESS D8 (V4.7) CONTROL PANEL – INSTALLER MANUAL
QUICK START PROGRAMMING
Use one of these programming summaries for fast setup of your D8 as a Local,
Audible Monitored or Central Station Monitored system.
The control panel will be ready for use immediately.
QUICK START 1
LOCAL SYSTEM
Quick Start 1 shows you how to
change User Code 1 (the Master
Code).
By default, the dialler is disabled
until programmed.
1
Enter User Program Mode Program Light is ON
2
Selects the option for User Code 1
3
Enter the new User Code Can be 3 to 6 digits long
4
Enter the new User Code again
5
To exit Program Mode
STEP
QUICK START 1 - step by step
DESCRIPTION COMMENT
Program light turns OFF
KEY STROKES
2
3
1
1 1
The code is displayed by the
keypad lights, followed by 3 beeps
new
The code is displayed by the
keypad lights, followed by 3 beeps
existing
QUICK START 2
AUDIBLE MON I TOR ING
Quick Start 2 shows you how
to change User Code 1 (the
Master Code), enable Audible
Monitoring and program 1
telephone number. This will
enable the dialler to report
alarms to any telephone
including mobile phones.
QUICK START 2 - step by step
Enter User Program Mode
Enter Installer Program Mode
Program Light is ON
Program Light is FLASHING
Selects the option for User Code 1
Enter the new User Code Can be 3 to 6 digits long
Enter the new User Code again
At P86E, turns ON option 4
Selects the option for Telephone No.1
Enter the telephone number
Audible Monitoring enabled
Can be up to 15 digits long
To exit Program Mode Program light turns OFF
KEY STROKES DESCRIPTION COMMENT
1
2
3
4
5
6
7
8
9
STEP
1 1
8 6
4
7
0
Up to 15 digits
2
3
1
0 0 0 0 0 0
The code is displayed by the
keypad lights, followed by 3 beeps
new
The code is displayed by the
keypad lights, followed by 3 beeps
existing
See page 58 for further information on the operation of Audible Monitoring.
7
2
QUICK START 3 - step by step
Enter User Program Mode
Enter Installer Program Mode
Program Light is ON
Program Light is FLASHING
Selects the option for User Code 1
Enter the new User Code Can be 3 to 6 digits long
Enter the new User Code again
At P86E, turns ON option 2
Selects the option for Telephone No.1
Enter the Telephone Number
Enter the Account Number
Central station Monitoring enabled
Existing Ph No (if any) displayed
Can be up to 15 digits long
Must be 4 digits
To exit Program Mode Program light turns OFF
DESCRIPTION COMMENT
1
2
3
4
5
6
7
8
9
10
STEP
1
2
3
KEY STROKES
1 1
8 6
2
7
0
Up to 15 digits
2
3
1
0 0 0 0 0 0
The code is displayed by the
keypad lights, followed by 3 beeps
new
The code is displayed by the
keypad lights, followed by 3 beeps
existing
Option P86E 2E is ON by factory default. This option only needs to be turned ON if previously
programmed OFF.
Account Number to identify the premises - supplied by the Central Station
The tation’s receiver telephone number - supplied by the Central StationCentral S
QUICK START 3
CENTRAL STATION
MONITORING
Quick Start 3 shows you how
to change User Code 1 (the
Master Code), enable Central
Station Monitoring and program
one telephone number. This
will enable the dialler to report
alarms to a Central Station.
* Factory default Master Code is: 123
* Factory default Installer Code is: 000000
** User codes must not start with 0.

Ness D8 Specifications

General

Brand	Ness
Model	D8
Category	Control Panel
Language	English