Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu A Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
134 Installation and System Design Guide
Issue Number: 1
Table 5-11 SMARTCARD and SD card codes
Where yyy indicates the block number 001 to 999.
If the NV Media Card read only flag, 9888 is set then only codes 6yyy or 9777 are effective.
5.16.1 NV Media Card trips
The NV Media Card should not be removed during data transfer as the drive will produce a trip. If this occurs, then either the transfer should be re-
attempted or in the case of a NV Media Card to drive transfer, default parameters should be loaded.
After an attempt to read, write or erase data from a NV Media Card a trip is initiated if there has been a problem with the command. See the
diagnostics section for more information on the NV Media Card trips.
5.16.2 Data block header information
Each data block stored on a NV Media Card has header information as detailed in the following parameters:
• Media card file number (N03)
• Media card file type (N04)
• Media card file version (N05)
• Media card file checksum (N06)
The header information for each data block used can be viewed in Media card file type (N04) to Media card file checksum (N06) by increasing or
decreasing the data block number set in Media card file number (N03). If there is no data on the card Media card file number (N03) can only have a
value of 0.
5.17 NV Media Card transferring data
Data transfer, erasing and protecting the information is performed by entering a code in
Pr mm00
and then resetting the drive as shown in
Table 5-11
SMARTCARD and SD card codes.
The whole card may be protected from writing or erasing by setting the read-only flag as detailed in Table 5-11 SMARTCARD and SD card codes.
5.17.1 Reading from the NV Media Card
• 6yyy - Reading from the NV Media Card
When data is transferred to the drive, using 6yyy in Pr mm00, it is transferred to the drive RAM and the EEPROM. A parameter save is not required
to retain the data after power down. If the option modules installed are different between source and destination drives, the menus for the option
module slots where the option module categories are different are not updated from the NV Media Card and will contain their default values. The drive
will produce a 'Card Option' trip if the option module installed to the source and the destination drives are different or are in different slots.
Code Operation SMARTCARD SD card
2001 Transfers all drive parameters (including SI options) to parameter file 001 and sets the block as bootable.
99
4yyy Transfers all drive parameters (including SI options) to parameter file yyy.
99
6yyy Load the drive parameters from parameter file yyy
99
7yyy Erase parameter file yyy.
99
8yyy Compare drive parameters with parameter file yyy.
99
9555 Clear the warning suppression flag
99
9666 Set the warning suppression flag
99
9777 Clear the read-only flag
99
9888 Set the read-only flag
99
9999 Erase and format the NV Media Card
9
15yyy Transfer a program from an option module in slot 1 to a option module applications file
9
16yyy As 15yyy, but for slot 2
9
17yyy As 15yyy, but for slot 3
9
18yyy Load a program to the option module in slot 1 from an option module applications file
9
19yyy As 18yyy, but for slot 2
9
20yyy As 18yyy, but for slot 3
9
21yyy As 15yyy, but for slot 4
9
22yyy As 18yyy, but for slot 4
9
40yyy
Backup all drive data (parameter differences from defaults, applications programs and miscellaneous
options module data), including the drive name; the store will occur to the </MCDF/driveyyy/> folder on
the NV Media Card; if it does not exist, it will be created. Because the name is stored, this is a backup,
rather than a copy. The command will clear when all drive and option module data is saved.
9
60yyy
Load all drive data (parameter differences from defaults, applications programs and miscellaneous
options module data); the load will come from the </MCDF/driveyyy/> folder on the NV Media Card. The
command code will clear once all drive and option module data has been loaded.
9
To Next Page
Loading...
