Nidec E300 Series - Menu Y: Data Logger

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu A Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
Installation and System Design Guide 241
Issue Number: 1
8.19 Menu Y: Data Logger
Menu Y Data Logger provides a 4 channel Data Logger which can be used to capture events on the Elevator drive also using an additional user
defined trigger. The 4 channels of the Data Logger can be user configured to the Elevator drive software control parameters and, or IO parameters to
capture events from unstable operation to incorrect control inputs.
The default configuration for the 4 Data Logger channels = 0.000 and are all fully user definable. The sources do not operate in the same way as
normal source parameters in that the input to the Data Logger is the actual value of the source parameter and not a value scaled to a percentage
based on the range of the source parameter.
Figure 8-26 Menu Y Data logger logic diagram
Parameter
Range(Ú)Default(Ö)
Type
Open-Loop RFC-A RFC-S Open-Loop RFC-A RFC-S
Y02 Data Logger Trace 1 Source A00 to AC99 A00 RW Num PT US
Y03 Data Logger Trace 2 Source A00 to AC99 A00 RW Num PT US
Y04 Data Logger Trace 3 Source A00 to AC99 A00 RW Num PT US
Y05 Data Logger Trace 4 Source A00 to AC99 A00 RW Num PT US
Y06 Data Logger Trigger Off (0) or On (1) Off (0) RW Bit
Y07 Data Logger Trigger Source A00 to AC99 A00 RW Num PT US
Y08 Data Logger Trigger Threshold -2147483648 to 2147483647 0 RW Num US
Y09 Data Logger Trigger Invert Off (0) or On (1) Off (0) RW Bit US
Y10 Data Logging Mode Single (0), Normal (1), Auto (2) Single (0) RW Txt US
Y11 Data Logger Arm Off (0) or On (1) Off (0) RW Bit NC
Y12 Data Logger Data Not Ready Off (0) or On (1)
RO Bit ND NC PT
Y13 Data Logger Saving Data Off (0) or On (1)
RO Bit ND NC PT
Y14 Data Logger Sample Time 1 to 200 1 RW Num US
Y15 Data Logger Trigger Delay 0 to 100 % 0 % RW Num US
Y16 Data Logger Time Period 0.00 to 200000.00 ms
RO Num ND NC PT
Y17 Autosave Mode
Disabled (0), Overwrite (1),
Keep (2)
Disabled (0) RW Txt US
Y18 Data Logger Autosave File Number 0 to 99 0 RO Num PS
Y19 Data Logger Autosave Reset Off (0) or On (1) Off (0) RW Bit
Y20 Data Logger Autosave Status
Disabled (0), Active (1),
Stopped (2), Failed (3)
Disabled (0) RO Txt PS
RW Read / Write RO Read-only Bit Bit parameter Txt Text string Date Date parameter Time Time parameter
Chr
Character
parameter
Bin Binary parameter IP IP address Mac MAC address Ver Version number SMP
Slot, menu,
parameter
Num Number parameter DE Destination ND No default value RA Rating dependent NC Non-copyable PT Protected
FI Filtered US User save PS Power-down save
Y02
Data Logger
channel 1
Y04
Y05
Y12
Data Logger
Y10 Data Logger mode
Y14 Data Logger sample time
Y15 Data Logger trigger delay
Y16 Data Logger time period
Y17 Data Logger auto -save mode
Y18 Data Logger auto -save file number
Y19 Data Logger auto -save reset
Y20 Data Logger auto -save status
0
1
Data Logger
channel 2
Data Logger
channel 3
Data Logger
channel 4
Y03
Y13
Data Logger data
not ready
Data Logger
saving data
Y11
Data Logger
arm
Y06
Y07
Y08
Data Logger
trigger
Data Logger
Trigger source
Data Logger
trigger threshold
Y09
Data Logger
Trigger invert
+
-
OR