Nidec E300 Series - Page 293

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu A Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
Installation and System Design Guide 293
Issue Number: 1
Table 9-15 Serial communications look up table
No Trip No Trip No Trip
2
Over Volts 78 Autotune No Dir 189 Encoder 1
3
OI ac 79 Analog No Dir 190 Encoder 2
4
OI Brake 80 Fast Start En 191 Encoder 3
5
PSU 81 SPD / Dir Select 192 Encoder 4
6
External Trip 82 I Limit Timeout 193 Encoder 5
7
Over Speed 83 550 Hz Limit 194 Encoder 6
8
Inductance 84 Encoder Not Init 195 Encoder 7
9
PSU 24 85 No DCP Module 196 Encoder 8
10
Th Brake Res 86 - 89 User Trip 86-89 197 Encoder 9
11
Autotune 1 90 Power Comms 198 Phasing Error
12
Autotune 2 91 User 24 V 199 Destination
13
Autotune 3 92 OI Snubber 200 Slot 1 HF
14
Autotune 4 96 User Prog Trip 201 Slot 1 Watchdog
15
Autotune 5 97 Data Changing 202 Slot1 Error
16
Autotune 6 98 Out Phase Loss 203 Slot1 Not Fitted
17
Autotune 7 101 OHt Brake 204 Slot1 Different
18
Autotune Stopped 109 OI dc 205 Slot2 HF
19
Brake R Too Hot 110 Undefined 206 Slot2 Watchdog
20
Motor Too Hot 112 - 119 User Trip 112-119 207 Slot2 Error
21
OHt Inverter 120 ENP Bad Header 208 Slot2 Not installed
22
OHt Power 121 ENP Drive Mode 209 Slot2 Different
23
OHt Control 122 ENP Encoder 210 Slot3 HF
24
Thermistor 123 ENP Write 211 Slot3 Watchdog
25
Th Short Circuit 124 ENP Read 212 Slot3 Error
26
I/O Overload 125 - 129 User Trip 125-129 213 Slot3 Not Fitted
27
OHt dc bus 130 DCP Initialise 214 Slot3 Different
28
An Input Loss 1 131 DCP4 Distance 215 Option Disable
29
An Input Loss 2 132 DCP Dir Change 216 Slot App Menu
30
Watchdog 133 DCP CRC 217 App Menu Changed
31
EEPROM Fail 134 DCP Transmit 218 Temp Feedback
33
Resistance 135 DCP Wire Break 219 An Output Calib
36
User Save 136 DCP Bad Sequence 220 Power Data
37
Power Down Save 137 - 159 User Trip 137-159 221 Stored HF
38
Low Load 162 Encoder 12 224 Drive Size
40 - 59
User Trip 40-59 163 Encoder 13 225 Current Offset
60
Freeze protect 174 Card Slot 226 Soft Start
61
Drive rating 175 Card Product 227 Sub-array RAM
62
Speed Err 177 Card Boot 247 Derivative ID
63
Distance Err 178 Card Busy 248 Derivative Image
64
Feedback Rev 179 Card Data Exists 249 User Program
65
Fast Disable Err 180 Card Option 250 Slot4 HF
66
STO Ctrl Err 181 Card Read Only 251 Slot4 Watchdog
67
Current On Stop 182 Card Error 252 Slot4 Error
68
Brk Ctrl Release 183 Card No Data 253 Slot4 Not Fitted
69
Fast Start Err 184 Card Full 254 Slot4 Different
70
Motor Contactor 185 Card Access 255 Reset Logs
72
Brake Contact 186 Card Rating
76 Dir change 187 Card Drive Mode
77 Ctrl Watchdog 188 Card Compare