Nortek 2GIG eSeries GC2e - Zone Numbering; Zone Numbering Ranges

To Next Page

To Previous Page

GC2e Wireless Security System | Installation and Programming Guide

Zone Numbering

Zones Descriptions

1-48 Wireless Zones

47-48 Wireless Cross-Sensor Zone

49-50 Wired Zones

51-58 Keyfobs

59-62 Keypads

63-74 Wireless Zones

92 Duress

95 Fire

96 Medical

99 Police Panic

The Control Panel supports 60 wireless protection zones. When programming zones, keep the following numbering ranges

in mind:

Main Page

Default Chapter3
- Table of Contents3
Introduction6
- About this Guide6
- About the 2GIG Go!Control System6
- Important Information6
- Installing the System in Residential Settings6
- Installing the System in Commercial Settings7
- System Features7
- Optional Accessories8
- 2GIG Gc2E Security Panel XCVR Compatibility8
System Configuration9
Control Panel Features10
- External Features10
- Internal Features11
Installation Outline12
Wireless Installation Tips13
Sensors and Accessories14
- Wireless System Sensors14
- Wireless System Esensors14
- System Accessories14
Installation15
- Control Panel Mounting Plate15
- Wireless Sensors16
- Hardwired Loop16
- Wiring16
- Remote Alarm Sounder16
- LTE (Cellular) Radio Module17
- Control Panel Wiring Diagram18
- Control Panel Wiring19
- Terminal Block Wiring Diagram19
- Backup Battery Connection and Power Supply Wiring19
- Wire Size and Length19
- Control Panel and Power Supply Mounting20
Commercial Installations21
NFPA Standard 7222
Main Display Screens23
- Home Screen23
- Security Screen23
- Arming Screen23
- Menu Screen23
- System Status Screen24
Toolbox and Installer Toolbox25
- Toolbox Screens25
- Accessing the Toolbox25
- Installer Toolbox Screens25
- Accessing the Installer Toolbox25
- Accessing the System Configuration for System and Sensor Programming25
- System Configuration Screens26
System Status Icons27
- AC Power On/Off27
- Sounder Disabled27
- Low Backup Battery27
- Test Mode27
- Touch Screen Keypad Traffic27
- Cell Radio27
- Interior Sensor Open27
Programming Navigation28
- Questions Without Sub-Options28
- Questions with Sub-Options28
- Questions with Data Entry28
- Additional Buttons29
Programming Outline30
- ANSI/SIA CP-01 Compliance30
Programming Question Table31
Zone Numbering34
Sensor Types (Zones)35
- Sensor Type (Zone)36
- Description37
Voice Descriptors37
2GIG Eseries Equipment Codes40
Installer Programming40
- Wireless Zones - Gc2E & Gc3E Esensor Equipment Codes40
- Account Registration40
- Wireless (RF) Sensor Programming40
  - Q1: RF Sensor Programming Outline41
- Summary of RF Sensor # Screen41
- RF Sensor Programming Questions41
- Wired Sensor Programming43
  - Q2: Wired Sensor Programming Outline44
- Summary of Wired Sensor # Screen44
- Wired Sensor Programming Questions44
- Wireless (RF) Key Fob Programming46
- Key Fob Programming Outline47
  - Q3: RF Key Fob Programming Outline47
- Summary of RF Key Fob # Screen47
- RF Key Fob Programming Questions47
- Wireless (RF) Keypad Programming48
- RF Keypad Programming Outline49
  - Q4: RF Key Pad Programming Outline49
- Summary of RF Keypad Screen49
- RF Keypad Programming Questions49
Control Panel Programming51
- Programming Questions51
Final Installation Setup61
- Exiting Programming (System Configuration)61
- Access the Installer Toolbox63
- Disable/Enable Sounder63
- Disable the Sounder63
- Enable the Sounder63
- Sensor Type (Zone) Report Test63
- Walk Test63
- Radio Status Test64
- Cell Phone Test64
- Restore Default System Configuration65
- Soft Reset65
- Hard Reset65
Regulatory Information66
- Wireless Product Notice66
- FCC Notice66
- Industry Canada Notices66
- Commercial Regulatory Listings67
Limited Warranty68

Nortek 2GIG eSeries GC2e - Zone Numbering; Zone Numbering Ranges

Table of Contents

Related product manuals