Nortek 2GIG eSeries GC2e - eSeries Equipment Codes; Wireless Zones - GC2 e & GC3 e eSensor Equipment Codes; Installer Programming

GC2e Wireless Security System | Installation and Programming Guide
©2020 Nortek Security & Control LLC. All rights reserved. 38 2GIG is a registered trademark of Nortek Security & Control LLC.
Installer Programming
Account Registration
Register the account to enroll the Control Panel with the remote
service provider’s Central Staon.
Typically, the account registraon data is created with the service
installaon contract and then stored in a database managed by
the Central Staon. The data includes items such as the customer
name, address, and the Central Staon telephone number, and the
account number assigned to the Control Panel.
If you will be installing the 2GIG Go!Bridge IP Communicator,
addional registraon informaon is required. For details, see
the Installaon Instrucons included with the Go!Bridge IP
Communicator.
Wireless (RF) Sensor Programming
The Control Panel can be programmed with up to 60 RF sensors
of dierent types. In addion to the 60 mul- purpose RF sensors,
you can also program eight (8) RF remote control key fobs and four
(4) RF remote control keypads into the system.
RF sensors # 01‐48 and #63‐74 report as wireless zones 01‐ 60.
Programming quesons for RF sensor programming include:
• Q1: Select RF Sensor Number. Select sensor number 01-48 or
63-74.
• Q: Select RF Sensor # Type. Select (01) Exit/Entry 1, (02)
Exit/Entry 2, (03) Perimeter, and so on. For opons, see
“Zone Numbering” on page 32.
• Q: Select RF Sensor # Equipment Type. Some sensor types
ask for the equipment type, others do not. See “Q: Select
RF Sensor # Equipment Type” on page 40.
• Q: Select RF Sensor # Equipment Code. Select the four (4)-
digit equipment code for the sensor model. See “Equipment
Codes” on page 37.
• Q: Enter RF Sensor # Other Equipment Code. If you select
(0000) Other in the previous queson, you must enter this
code.
• Q: Enter RF Sensor # Serial #. Enter the serial number
(typically a label on the sensor or its packaging) or tap Shi
then Learn on the panel. Then trip the sensor to transmit
the serial number to the panel.
• Q: Select RF Sensor # Equipment Age. Specify whether the
sensor is (0) New or (1) Exisng.
• Q: Select RF Sensor # Loop Number. Specify the
appropriate loop number(s) for the sensor. See “Q: Select RF
Sensor # Loop Number (1 to 3)” on page 40.
• Q: Select RF Sensor # Dialer Delay. Specify whether to use
delayed or instant digital communicator reports for the
sensor. The delay me is set on the Dialer Abort screen.
• Q: Construct RF Sensor # Voice Descriptor. Specify the
name assigned to the sensor that is announced if this
feature is programmed.
• Q: Select RF Sensor # Reports. Specify (0) Disabled or (1)
Enabled whether or not RF sensors trigger a report to the
Central Staon.
• Q: Select RF Sensor # Supervised. Specify whether or not
the Control Panel checks for status reports from the sensor.
• Q: RF Sensor # Chime. Select voice announcement and
chime opons for the sensor.
2GIG eSeries Equipment Codes
Wireless Zones - GC2e & GC3e eSensor Equipment Codes
When programming eSensors (Wireless Sensors & Keyfobs) the equipment code must match the sensor being installed.
*Available soon for GC2e
**Available soon for GC2e & GC3e
Code Description
2058** eSeries Smoke Detector (USA) (Use for all loops (1 2 3)
2061* eSeries Tilt Sensor
2065* eSeries Flood Sensor
2067* eSeries Repeater
2069* eSeries FireFighter SMKT/CO Listener
2070* eSeries Water Sensor
2860 eSeries CO Detector (USA)
2862 eSeries Thin Door/Window Contact
2863 eSeries Recessed Door Contact
2864 eSeries Glass Break Detector
2865 eSeries Outdoor Door/Window Sensor
2866 eSeries Key FOB
2868* eSeries Panic
2869 eSeries PIR with Pet Immunity
2873* eSeries Takeover Module
Note: For sensors with multiple loops, the eSeries equipment codes must be used for all programmed loops.