Nortek 2GIG eSeries GC2e - Wireless (RF) Sensor Programming; Q1: Select RF Sensor #

Q1: SELECT RF SENSOR #
PRESS TO FINISH PROGRAMMING SENSOR
THEN PRESS TO PROGRAM THE NEXT SENSOR
OR PRESS TO JUMP TO Q2: WIRED SENSOR PROGRAMMING
Q: SELECT RF SENSOR # TYPE
Q: SELECT RF SENSOR #
EQUIPMENT TYPE
Q: SELECT RF SENSOR #
EQUIPMENT TYPE
Q: ENTER RF SENSOR OTHER
EQUIPMENT CODE
(Only appears if (0000) Other
was selected in previous queston)
Q: SELECT RF SENSOR SERIAL
NUMBER
Q: SELECT RF SENSOR EQUIPMENT
AGE
Q: SELECT RF SENSOR LOOP
NUMBER
Q: SELECT RF SENSOR DIALER
DELAY
Q: CONSTRUCT RF SENSOR VOICE
DESCRIPTOR
Q: SELECT RF SENSOR REPORTS
Q: SELECT RF SENSOR SUPERVISED
Q: SELECT RF SENSOR CHIME
Q1: RF Sensor Programming Outline
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD
PRESS FOR NEXT OPTION
shift
ENTER ON KEYPAD OR PRESS
OR
THEN TRIP SENSOR TO SEND SIGNAL
learn
PRESS FOR EACH WORD
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
shift
edit next
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
skip
GC2e Wireless Security System | Installation and Programming Guide
©2020 Nortek Security & Control LLC. All rights reserved. 39 2GIG is a registered trademark of Nortek Security & Control LLC.
Figure 45 RF Sensor Programming Outline
Q1: RF Sensor Programming Outline Summary of RF Sensor # Screen
Aer seng all the opons for a sensor, the RF sensor summary
screen is displayed. The screen can also be displayed for
programmed sensors during RF sensor program eding by tapping
the Sum buon.
• While programming each RF sensor remember that the ←
and → arrow bu ons step through each of the RF sensor
numbers.
• To return to programming, tap Edit Current or Edit Next.
• Tap Skip to go to queson number Q2 (Wired Sensor
Programming). See “Wired Sensor Programming” on page 41.
Figure 46
Summary of RF Sensor # Screen
RF Sensor Programming Questions
Q1: Select RF Sensor # (01-48, 63-74)
Up to 60 wireless RF sensors can be used with each Control Panel.
The opons for each sensor are programmed with sub-opon
quesons.
1. Enter the RF sensor number or tap the ← or → arrows to
select it.
2. Program the sensor details by using the ↑ and ↓ arrows to
select each of the sub-opons.
NOTE: To skip Q1 and jump directly to Q2 for Wired Sensor
Programming, tap Skip.
Q: Select RF Sensor # Type
DEFAULT: (00) Unused
Answer this queson to dene the sensor type (zone). Simply
enter the appropriate code (see table below) or tap the ← or →
arrows to select the desired zone.
In the table below, a “Y” indicates the sensor type can be assigned.
A “N” indicates the sensor type is not used, an d an asterisk (*)
denotes that selecng this sensor type also requires you to answer
the Q: Select RF Sensor # Equipment Type queson.
Scroll between op ons using the ← and → arrows. Move to
the previous or next prompt by tapping the ↑ and ↓ arrows.
1. 1 To program another sensor tap Next.
2. To exit programming, tap Skip then End and Exit. Upon
exit, the panel takes several seconds to restart. *Only use
d for “other” equipment
**Tap Insert for each word. To select from the list, you can use
the keypad or tap the ← or → arrows.
Sensor Types (Zone) RF Wired
(00) Unused Y Y
(01) Exit/Entry 1 Y Y
(02) Exit/Entry 2 Y Y
(03) Perimeter Y Y
(04) Interior Follower* Y Y
(05) Day Zone Y Y
(06) 24-Hour Silent Alarm* Y Y
(07) 24-Hour Audible Alarm* Y Y
Installer Programming