Nortek 2GIG eSeries GC2e - RF Keypad Programming; Q4: RF Key Pad Programming Outline; RF Keypad Programming Questions

Q1: SELECT KEYPAD #
PRESS TO FINISH PROGRAMMING SENSOR
THEN PRESS TO PROGRAM THE NEXT SENSOR
OR PRESS TO JUMP TO Q2: WIRED SENSOR PROGRAMMING
Q: SELECT RF KEYPAD # USED
Q: SELECT RF KEYPAD #
EQUIPMENT CODE
Q: ENTER RF KEYPAD 3 OTHER
EQUIPMENT CODE
(Only appears if (0000) Other
was selected in previous queston)
Q: ENTER RF KEYPAD
SERIAL NUMBER
Q: SELECT RF KEYPAD #
EQUIPMENT AGE
Q: SELECT RF KEYPAD #
EMERGENCY KEYS
Q: CONSTRUCT FOB #
VOICE DESCRIPTOR
Q4: RF Key Pad Programming Outline
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD
PRESS FOR NEXT OPTION
shift
ENTER ON KEYPAD OR PRESS
OR
THEN SEND SIGNAL
FROM KEY FOB
learn
PRESS FOR EACH WORD
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
shift
edit next
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
skip
GC2e Wireless Security System | Installation and Programming Guide
©2020 Nortek Security & Control LLC. All rights reserved. 47 2GIG is a registered trademark of Nortek Security & Control LLC.
RF Keypad Programming Questions
Q4: Select RF Keypad # (1 to 4)
Up to four (4) wireless keypads can be programmed for use with each
Control Panel. The opons for each sensor are programmed with sub-
opon quesons:
• Begin by entering the RF Keypad number or select it using the ← or
→ arrows.
• Program the RF keypads by using the ↑ and ↓ arrows to select the
sub-opons.
To skip RF Keypad programming, tap Skip to jump from queson Q4 to
queson Q5 (Exit Delay programming).
Q: Select RF Keypad (#) Used (0 to 1)
DEFAULT: (0) Unused
Users can use RF keypads together with a Control Panel or not.
• The default seng (0) Unused sets all RF keypads as unused.
• To en able programming for this RF keypad, select (1) Used.
Q: Select RF Keypad (#) Equipment Code (0-9999)
DEFAULT: (0000) Other
The RF keypad equipment code denes the sensor’s manufacturer and
type.
• The default seng is (0000) Other.
• Select ( 0867) 2GIG Wireless Keypad.
• Select (1059) 2GIG TS1 Wireless Touchscreen Keypad.
NOTE: 2GIG Wireless Touch Screen Keypad is not intended for UL 985:
Household Burglar‐Alarm System Units installaons.
Q: Enter RF Keypad # Other Equipment Code (0-9999)
DEFAULT: 0
NOTE: This queson is only displayed if (0000) Other is selected as the RF
keypad’s equipment code.
IMPORTANT: The equipment code is a four (4)-digit code that is assigned
to the appropriate keypad model being used.
• Enter the equipment code number for the RF Keypad.
Q: Enter RF Keypad# Serial Number (7 Digits)
DEFAULT: 0000000 or RF Keypad (#) Keypad ID (read‐only)
Serial numbers for standard wireless keypads can be manually entered
or learned from the keypad. For Wireless Touch Screen Keypads, serial
numbers can only be learned from the keypad. Read-only with Keypad ID’s
refer to the installer being unable to manually input an id.
Standard Keypads:
• For manual entry, enter the Wireless Keypad that was logged for
the keypad being programmed. Tap the Shi buon to access alpha
characters.
• For automac entry, tap Shi and then Learn. This places the
Control Panel into learning mode. When you trigger the keypad the
sensor for the keypad being programmed, it sends its serial number
to the Control Panel.
Wireless Touch Screen Keypads (only available in some regions):
• For Wireless Touch Screen Keypads tap Learn. The Control Panel
displays the “Pair with TS‐1. Iniang learning process”. Tap the
keypad’s Pair with Panel buon. When complete, the keypad
and the Control Panel display “The learn operaon succeeded”
message.
• The Control Panel displays “RF Keypad (#1-4)” to idenfy the
keypad.
Scroll between op ons using the ← and → arrows. Move to the
previous or next prompt by tapping the ↑ and ↓ arrows.
1. To program another sensor tap Next.
2. To exit programming, tap Skip, then End, and then Exit.
Upon exit, the panel takes several seconds to restart.
3. Tap Skip to jump to queson Q5.
Summary of RF Keypad Screen
Aer seng all the opons for a sensor, the RF keypad
summary screen is displayed. The screen can also be displayed
for programmed RF keypads by tapping the Sum buon.
• To return to programming, tap the Edit Current or Edit
Next buons.
• Tapping Skip goes to queson Q5 (Control Panel
programming).
• To exit programming, tap Skip then End and Exit. Upon
exit, the Control Panel takes several seconds to restart.
RF Keypad Programming Outline
Q4: RF Key Pad Programming Outline
Figure 50 Key Pad Programming Outline
Installer Programming