$
HQGL[ $ 5HOHDVLQ
$
OLFDWLRQV
How to Program a Releasing Zone
52 AFC-600 Programming PN 51032:A 3/8/99
8VLQ
&URVV=RQHV
3XU
RVH RI &URVV =RQHV
Using Cross Zones lets you program the control panel to activate a Releasing Zone and
any output mapped to the Releasing Zone. (If not using Cross Zones, set CROSS= to
N.) Table 29 summarizes the types of Cross Zones and the conditions for activating a
Releasing Zone.
7DEOH &URVV =RQH 6HOHFWLRQV
+RZ &URVV =RQHV :RUN
Figure 65 contains an illustrated example of how Cross Zones work, using five Cross
Zone selections (four detectors and an NAC mapped to Releasing Zone R1). Table 30
lists the cross zone selections and the conditions that activate the Releasing Zone.
)LJXUH ,OOXVWUDWHG ([DPSOH RI &URVV =RQH 3URJUDPPLQJ
Continued on the next page...
1RWH
2QO
WKH ILUVW 6RIWZDUH
=RQH == OLVWHG LQ WKH
]RQH PD
LV XVHG WR
GHWHUPL QH & URV V =
1RWH
6
HFLDO =RQHV
55 D
HDU LQ WKH &%(
OLVW DV =5=5 )RU
H[DP
OH 5 D
HDUV LQ
WKH &%( OLVW DV =5
Type Activates when
Y Two or more detectors are alarmed that are mapped to one of the ten Releasing
Zones (R0-R9).
Z Two or more detectors are alarmed that are mapped to two different software zones
and mapped to one of the ten Releasing Zones (R0-R9).
H At least one smoke detector mapped to one of the ten Releasing Zones (R0-R9) is
alarmed and at least one heat detector mapped to one of the ten Releasing Zones
(R0-R9) is alarmed.
6RIWZDUH
=RQH =
'
&%( OLVW = =5
%
1$&
'HWHFWRU
6PRNH
'
'HWHFWRU
6PRNH
'
'HWHFWRU
6PRNH
'
'HWHFWRU
+HDW
5HOHDVLQ
=RQH =5
&%( OLVW = =5
&%( OLVW = =5
&%( OLVW = =5
&%(OLVW ==5
6RIWZDUH
=RQH =
352*50 602.( 3+272 '(7(&725 $''5 '
=2 =5 = = = $/ 3$ '
352*50 602.( 3+272 '(7(&725 $''5 '
=2 =5 = = = $/ 3$ '
352*50 602.( ,21 '(7(&725 $''5 '
=2 =5 = = = $/ 3$ '
352*50 602.( +($7 '(7(&725 $''5 '
=2 =5 = = = $/ 3$ '
352*50 %(// &,5&8,7 3$1(/ &,5&8,7 12
= =5 = = = ,6 : %
&%( OLVW = =5
&%( OLVW = =5
&%( OLVW = =5
&%( OLVW = =5
&%( OLVW = =5
Technical Manuals Online! - http://www.tech-man.com
To Next Page
Loading...
Need help?
General
