Omron ZN-CTX21 - Page 12

xi
3.4.1
Overview.............................................................................................................................. 3-6
(1) Setting Tool .......................................................................................................................... 3-6
(2) Logging Tool ........................................................................................................................ 3-6
(3) Momentary Value Display (SD Viewer ES)............................................................................ 3-6
(4) Integration and Summation Tool (Energy Viewer) ................................................................. 3-6
3.4.2 Installation............................................................................................................................ 3-6
3.5 Setting the Measurement Conditions ........................................................................................... 3-7
(1) Switching to "FUN" Mode ..................................................................................................... 3-7
(2) Setting the Number of Channels to Use (USECH) (Example: 2 Channels) ............................ 3-7
(3) Setting Measurement Target Circuit (TYPE) and Dedicated CT Type (CT) ............................ 3-8
(4) Setting Voltage of Measurement Target (VOLT) (Example: 100.0V) ...................................... 3-8
(5) Setting Power Factor (PF) and Frequency (FREQ) ............................................................... 3-8
3.6 Connecting to Network ................................................................................................................ 3-9
3.6.1 Preparation .......................................................................................................................... 3-9
3.6.2 Setting Portable Power Monitor IP Address ........................................................................ 3-10
(1) Switching to "FUN" Mode ................................................................................................... 3-10
(2) Setting ETC and IP to “DISP” ..............................................................................................3-11
(3) Changing IP Address (from factory default: 192.168.0.20 to 192.168.0.21) ......................... 3-12
3.6.3 Setting the PC IP Address .................................................................................................. 3-13
(1) Windows XP ...................................................................................................................... 3-13
(2) Windows Vista ................................................................................................................... 3-16
(3) Windows 7 ......................................................................................................................... 3-19
3.6.4 Connecting LAN Cable ....................................................................................................... 3-22
3.7 Mounting the Unit ...................................................................................................................... 3-23
3.7.1 Free-stand Installation ........................................................................................................ 3-23
3.7.2 Securing with Mounting Magnets ........................................................................................ 3-23
3.7.3 Securing with Mounting Screws .......................................................................................... 3-24
3.7.4 Screw Hook Mounting ........................................................................................................ 3-24
3.8 Attaching Dedicated CT to Measurement Target ........................................................................ 3-25
4. Setting the Unit (Unit Operation) ..................................................................................................... 4-1
4.1 Setting Procedure and Operation Modes ..................................................................................... 4-1
4.2 Settings (FUN Mode Operation) .................................................................................................. 4-2
4.2.1 Setting Item List ................................................................................................................... 4-2
4.2.2 Selecting "FUN" Operation Mode ......................................................................................... 4-5
4.2.3 Selecting Items .................................................................................................................... 4-6
4.2.4 Definition of Items ................................................................................................................ 4-7
(1) Ranking Clear (CLEAR) ....................................................................................................... 4-7
(2) Recording Interval (CYCLE) ................................................................................................. 4-7
(3) Timer Setting (TIMER) ......................................................................................................... 4-8
(4) Start Trigger (STRIG) ........................................................................................................... 4-8
(5) Start Time (STIME)............................................................................................................... 4-9
(6) End Trigger (ETRIG) ............................................................................................................ 4-9
(7) End Time (ETIME).............................................................................................................. 4-10
(8) Elapsed Time (ELPSD) ...................................................................................................... 4-10
(9) Measurement Mode (MODE)...............................................................................................4-11
(10) Recording Mode (REC) ...................................................................................................... 4-12
(11) Integrated Power Reset Interval (INTEG) ........................................................................... 4-12
(12) The Number of Channels to Use (USECH) ......................................................................... 4-13
(13) Measurement Target Circuit (TYPE) ................................................................................... 4-13
(14) Dedicated CT Type (CT)..................................................................................................... 4-13
(15) Voltage of Measurement Target (VOLT) .............................................................................. 4-13
(16) Power Factor (PF) .............................................................................................................. 4-14
(17) Frequency (FREQ) ............................................................................................................. 4-14
(18) Initialization (INIT) .............................................................................................................. 4-14
(19) Others (ETC) ..................................................................................................................... 4-15
(20) Reading Setting Data (RESTR) .......................................................................................... 4-15
(21) Writing the Setting Data (BCKUP) ...................................................................................... 4-16