Setup Menus
Off
Timer
Select
how
long
the
unit
remains
on
when
it
is
not
being
used.
Perform
step
1
of
"Accessing
the
Setup
Menus"
(-+
46).
(a
..
, to select "Setup", then
~
)
E)
..
,
to
select
"Off
Timer",
then
~
0",
to select
"2
Hours", "6 Hours"
or
"Off", then
~
oWhile pressing and holding
~,
press and hold the numbered button
ITJ,
(2),
or
[ID
corresponding to
the code set
in
step 4 for about 5
seconds to set.
o
~
to start auto setting.
The
following
dialog
appears
when
setting
is
complete.
~~0_~_OK~_to_co_m_p_le_te_._---=========J
Clock
Settings
414120061215 AM
CST
..
...
.
On
Time
Zone
EST
/
o
..
,
...
to
select
"Set
Code
1",
"Set
Code
2",
or
"Set
Code
3"
then
~
to
set.
( Set Clock Automatically )
After selecting
"Clock
Settings"
(-+
above,
step
3).
o
..
,
...
to select "Set Clock
Automatically", then
~
Perform
step 1
of
"Accessing
the
Setup
Menus"
(-+
46)
(a
..
, to select "Setup", then
~
)
E)
..
, to select "Clock Settings", then
.~
)
After selecting "Parental Rating"
(-+
47,
step
3)
(
To
change the password
(£)
Tips
To
clear the password
(-+
70,
To
reset
the
ratings
level
settings)
@ Notes
• Recording
may
fail
when
a wrong password
was
entered
for
scheduled recording settings.
• "V-chip" technology enables restricted shows
to
be
locked
according
to
TV
ratings.
•
The
V-chip
system
that
is
used
in
this
set
is
capable
of
blocking
"NR"
programs
(non
rated,
not
applicable
and
none)
as
per
FCC
Rules
Section
15.120(e)(2).
If
the
option
of
blocking
"NR"
programs
is
chosen
"unexpected
and
possibly
confusing
results
may
occur,
and
you
may
not
receive
emergency
bulletins
or
any
of
the
following
types
of
programming:"
-
Emergency
Bulletins
(Such
as
EAS
messages,
weather
warnings
and
others)
-Locally originated programming
•
News·
Political
- Public
Service Announcements
• Religious· Sports· Weather
oEnter a 4-digit password with the
\..
numbered buttons, then
~
o
..
,
...
to select "Change Password",
then~
oEnter the new password with the
numbered buttons, then
~
- A screen appears confirming that
you
have
set a password. Press
[OK].
Remote Control
Use
this function
to
synchronize
the
codes
for
the
remote
control
and
the
main
unit.
Perform
step
1
of
"Accessing the Setup
Menus"
(-+
46).
(a
..
, to select "Setup", then
~
)
E)
..
, to select "Remote Control",
then~
If
the
time
is
correct, [...]
to
select
"Yes",
then
[OK].
-
If
you
select
"No",
auto setting starts again, then
the
above
screen reappears. Repeat this step until
the
correct time
appears
.
•
If
the
clock
is
not correct, set
the
clock
with
"Adjust Time
Zone"
(-+
49)
or "Set Clock Manually"(-+
49).
RQT9046