Error Messages
Page
On the Unit's Display
HOD, RJO
•
An
error
has
occurred.
The
number
following
"H"
or
uP'
depends
on
the
status
of
the
unit.
-
(''0' stands for a service
Check
the
items
below
and
in
the
Troubleshooting
Guide.
If
the
service
number
still
does
number.)
not
disappear
after
the
check,
reset
the
unit
(-+
70,
"To
restore
the
unit
if
it
freezes"
).
•
If
the
service numbers
fail
to
clear,
note
the
service numbers
and
-
contact a qualified service person.
RC
0
('0'
stands
for
a •
The
remote
control
and
the
main
unit
are
using different
codes.
48
number.)
Change
the
code
on
the
remote control.
HARD
ERR
•
If
there
is
no
change after turning
the
unit
on
and
off,
consult
the
-
("HArd"
and
"Err"
are dealer
where
the
unit
was
purchased.
alternately displayed.)
NO
READ
•
The
disc
is
dirty
or
badly
scratched.
The
unit
cannot
record,
play,
or
edit.
63
("NO"
and
"REAd"
are
•
The
disc
may
be
incompatible or
of
poor
quality.
62,63,
alternately displayed.)
65
•
You
have
used
a lens cleaner
and
it
has
finished operation.
Press
3
[~
OPEN/CLOSE]
on
the main unit
to
eject
the
disc.
000000
•
Displayed
when
the
unit
is
started. This
is
not a malfunction.
-
•
The
unit
is
carrying out its recovery process.
You
cannot operate the
-
unit
while
"0'
is
displayed.
FULL
•
There
are
already
16
scheduled recording programs. Delete
23
unnecessary scheduled recording
programs.
UNSUPPORT •
You
have
inserted a disc
the
unit cannot play or record
on.
62,63
("UNSUP"
and
"POrt" are
•
You
tried
to
operate
with
a non-compatible
USB
memory.
64
alternately displayed.)
UNFORMAT
•
You
have
inserted a
new
DVD-RW/+RW
or a DVD-RAM/DVD-RW
21,44
("UNFOr"
and
"MAt"
are (DVD-Video format) recorded
on
other equipment.
You
can
format
the
alternately displayed.) disc
when
the
format confirmation screen
is
displayed.
"H]r
~
I"
is
displayed
on
the
•
This
unit
is
confirming that
it
is
connected
with
equipment compatible
-
unit's
display.
with
HDAVI
Control.
F74
•
The
HDMI
connection could not
be
authenticated due to a transfer
-
malfunction. Consult
the
dealer
where
the
unit
was
purchased.
F75
•
The
HDMI
connection could not
be
authenticated due to
an
internal
-
data malfunction. Consult
the
dealer
where
the
unit
was
purchased.
U59
•
The
unit
is
very
warm.
-
The
unit
switches
to
standby
for
safety
reasons.
Wait
for
about
30
minutes
until
the
message
disappears.
Reinstall
the
unit
in
an
area
with
adequate
ventilation.
Do
not
block
the
cooling
fan
on
the
rear
of
the
unit.
U61
•
There
was
a
power
failure
or
the
AC
power
supply
cord
was
disconnected
while
the
-
unit
was
on.
The
unit
is
carrying
out
its
recovery
process.
This
process
restores
the
unit
to
normal
operation.
The
unit
is
not
broken.
Wait
until
the
message
disappears.
U72
•
The
HDMI
connection acts unusually.
-
U73
-
The
connected equipment
is
not
HDMI
compatible.
-
Please
use
HIGH
SPEED
HDMI
cables
that
have
the
HDMIIogo
(as
shown
on
the
cover).
-
The
HDMI
cable
is
damaged.
U76
•
HDMI
cannot
be
output because
you
are
connected to a
model
that
-
does
not
support copyright protection.
U88
• There
was
something unusual detected
with
the
disc while recording
71
or
playing;
there was a power failure or
the
AC
power supply cord
was
disconnected while
the
unit
was
on.
The
unit
is
carrying out its
recovery process. This process restores
the
unit
to
normal operation.
.
The
unit
is
not broken. Wait until
the
message disappears.
U99
•
The
unit
fails
to
operate
properly.
Press
[POWER
<!Jill
on
the
main
unit
to
switch
-
the
unit
to
standby.
Press
[POWER
<!Jill
on
the
main
unit
again
to
turn
the
unit
on.
RQT9046
To Next Page
Loading...
Need help?
General
