Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 163
2) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF] Disables the [QUICK STARTUP] function.
[ON]
Enables the [QUICK STARTUP] function until the specied time set in [VALID PERIOD] elapses after
the projector enters the standby mode. The time until the projection starts after the power is turned on
will be reduced during the period when the [QUICK STARTUP] function is valid.
f Proceed to Step 3) when [ON] is selected.
3) Press the <ENTER> button.
f The [QUICK STARTUP] screen is displayed.
4) Press qw to switch [VALID PERIOD].
f The items will switch each time you press the button.
[30MIN.]
Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby
mode.
Select a desired valid period.
[60MIN.]
[90MIN.]
Note
f [QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].
f When [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK
STARTUP] function is valid.
f When [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the
projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].
f When [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks red while in the standby mode during the period
when the [QUICK STARTUP] function is valid. The power indicator <ON (G)/STANDBY (R)> lights up red when the specied time set in
[VALID PERIOD] elapses after the projector enters the standby mode.
f When [QUICK STARTUP] is set to [ON], the period when the [QUICK STARTUP] function is valid is counted as the projector runtime.
[POWER MANAGEMENT]
Set the function to save power consumption when there is no input signal.
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn o the light source of the projector when there is no input signal for specic
period. The time until the light source is turned o can be set.
1) Press as to select [POWER MANAGEMENT].
2) Press the <ENTER> button.
f The [POWER MANAGEMENT] screen is displayed.
3) Press as to select [NO SIGNAL LIGHTS-OUT].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[DISABLE] Disables the no signal lights-out function.
[10SEC.] - [5MIN.]
Turns o the light source when there is no input signal for the preset period.
Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.].
Note
f The [NO SIGNAL LIGHTS-OUT] setting item is common with the following menu item.
g The [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [NO SIGNAL LIGHTS-OUT]
f The fan will rotate to cool the projector while the no signal lights‑out function is operating and the light source is turned o. Also, the power
indicator <ON (G)/STANDBY (R)> blink green slowly.
f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on
again from the condition that the light source has turned o by this function.
g When the signal is input
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the <POWER ON> button is pressed
g When the operation to disable the shutter function (shutter: opened) is performed, such as pressing the <SHUTTER> button
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f The no signal lights-out function is disabled in following case.
g When [BACK COLOR] is set to [DEFAULT LOGO] or [USER LOGO], and the Panasonic logo or the image registered by the user is
displayed in the projected image
To Next Page
Loading...
