Panasonic PT-REQ12 Series

Chapter 1 Preparation — About your projector
38 - ENGLISH
Names and functions of the Function Board (optional)
This projector is equipped with Intel
®
Smart Display Module (Intel
®
SDM) specication slot.
Function Board supporting the Intel
®
SDM Small (Intel
®
SDM-S) or the Intel
®
SDM Large (Intel
®
SDM-L)
specication can be installed in the slot.
The terminal names of the optional Function Board with image input terminal to be used in this document is
dened here, and also their operations are explained. Also refer to the Operating Instructions of the Function
Board.
12G-SDI Terminal Board (Model No.: TY-SB01QS)
This board supports the HD-SDI signal, 3G-SDI signal, and 12G-SDI signal.
TY-SB01QS
1IN
4IN
3IN
2IN
OUT
3GSDI
12G/3G SDI
2 541 3
1 <SDI 4 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
2 <SDI 3 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
3 <SDI 2 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI).
4 <SDI OUT> terminal
This is an active through terminal to output the SDI signal
(HD-SDI/3G-SDI/12G-SDI) input to the <SDI 1 IN> terminal.
5 <SDI 1 IN> terminal
This is a terminal to input SDI signal (HD-SDI/3G-SDI/12G-SDI).
Note
f The <SDI 2 IN> / <SDI 3 IN> / <SDI 4 IN> terminals are used when the quad link signal is input. These terminals do not support input of
12G-SDI signal.
f When the projector is in standby mode, a signal is not output from the <SDI OUT> terminal.
f This projector is not equipped with an audio function so it is not possible to output audio, but the audio signal input to the <SDI 1 IN>
terminal is output from the <SDI OUT> terminal.
DIGITAL LINK Terminal Board (Model No.: TY-SB01DL)
This board supports the DIGITAL LINK signal.
DIGITALLINKOUT
LINK
HDCP
POWER
LINK
HDCP
DIGITALLINKIN / LAN
TY-SB01DL
52 3 4 3 41
1 Power status indicator <POWER>
On:
The power is supplied to the Function Board.
The [DISPLAY OPTION] menu → [SLOT IN] → [DIGITAL LINK
OUT] is set to [ENABLE].
Blinking:
The power is supplied to the Function Board.
The [DISPLAY OPTION] menu → [SLOT IN] → [DIGITAL LINK
OUT] is set to [DISABLE].
O󰀨:
The power is not supplied to the Function Board.
2 <DIGITAL LINK OUT> terminal
This is a terminal to output DIGITAL LINK signal input to the
<DIGITAL LINK IN/LAN> terminal.
3 Signal status indicator <LINK>
On:
DIGITAL LINK signal is input or output.
Blinking:
Only the Ethernet signal is input or output.
O󰀨:
DIGITAL LINK signal is not input or output.
4 Image signal indicator <HDCP>
On:
An image signal protected with HDCP is input or output.
Blinking:
An image signal that is not protected with HDCP is input or
output.
O󰀨:
An image signal is not input or output.
5 <DIGITAL LINK IN/LAN> terminal
This is a terminal to connect a device that transmits an image
signal via the LAN terminal. Also, this is the LAN terminal to
connect to the network.
Note
f To transmit the Ethernet and serial control signals using the <DIGITAL LINK IN/LAN> terminal, set the [NETWORK] menu → [ETHERNET
TYPE] to [DIGITAL LINK] or [LAN & DIGITAL LINK].
f To transmit the Ethernet signal using the <LAN> terminal equipped on the projector as standard, set the [NETWORK] menu → [ETHERNET
TYPE] to [LAN] or [LAN & DIGITAL LINK].