100
APEX615n Installation Guide
Motor Size: APEX603 Value Units Tolerance
1
2
3
4
5
Constant (s): Torque
Voltage (Sinusoidal)
Electrical Time
Mechanical Time
Thermal
114.6 (0.81)
49.0
9.7
-----
18
oz-in/A rms (Nm/A rms)
V rms/Krpm
milliseconds
milliseconds
minutes
± 10%
± 10%
nominal
nominal
nominal
6
7
8
9
10
11
Torque (s): Continuous, Stall
(NOTE: Values are with Continuous, Stall
rated and peak current, Continuous, Rated
lines 15 & 16 below. Peak, Max w/o Saturation
Drive current, and thus Static Friction
torque, may be lower.) Ripple (of Rated Torque)
367 (2.59)
346 (2.44)
356 (2.51)
1046 (7.38)
12.0 (0.08)
5
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
percent
min. [1]
min. [2]
min. [2]
min. [1]
max.
max. [3]
12
13
Speed: Rated
Maximum
3800 (63)
3800 (63)
rpm (rps)
rpm (rps)
reference
reference
14 Frequency Rated 126.7 Hz max.
15
16
Current: Rated
Peak
3.0
9.6
A rms
A rms
max. [1]
nominal
17
18
Voltage: Rated
Max
240
250
V rms
V rms
reference
maximum
19 Output Power Rated 1.0 (1.3) kWatts (hp) min. [1]
20 Inductance Terminal (line-line) 68 mH ± 30%
21 D.C. Resistance Terminal (line-line) 7.0 ohms ± 10 % [1]
22 Acceleration at Rated Torque 74150 rads/sec
2
Theoretical
23 Rotor Inertia 5.45 (99.6) oz-in
2
(kgm
2
∗ 1E-6) nominal
24 Damping 0.960 (0.0068) oz-in/krpm (Nm/krpm) nominal
25 Weight 9.0 (4.08) lbs. (kg) max.
26 Winding Temperature 170°C (338°F) [4] °C (°F) max.
27 Winding Temperature Rise (Above Ambient) [1] 145°C (293°F) °C (°F) reference
28 Insulation Class H — reference
29 Thermostat TRIP Temperature 170°C (338°F) °C (°F) ± 5° C
30 Thermostat RESET Temperature 135°C (275°F) °C (°F) ± 10° C
31 Dielectric Strength, (Winding-to-Frame) 1750 VAC min.
32 Winding Capacitance-to-Frame 0.00122 µF max.
33 IP Classification 65 [8] rated standard
34 Shaft: Radial-Play At End
At Faceplate
14E-6 (80E-9)
8.0E-6 (45E-9)
in/lb (m/N)
in/lb (m/N)
reference
reference
35 Material [5] RC-#30 — reference
36 Magnet Type NdFeB — —
37 Loading [6] 1000 rpm (17 rps)
2000 rpm (33 rps)
3000 rpm (50 rps)
4000 rpm (67 rps)
5000 rpm (83 rps)
85.4 (380)
67.8 (302)
59.1 (263)
53.8 (239)
50 (222)
lbs. (N)
lbs. (N)
lbs. (N)
lbs. (N)
lbs. (N)
max. [7]
max. [7]
max. [7]
max. [7]
max. [7]
38 Motor Vibration N ISO 2373 Standard
39 Bearing Class, Internal/External 1/Class 3 ABEC/AFBMA reference
40 Bearing Grease SRI #2 Manufacturer reference
41 Shaft Seal Pressure 3 (0.21) psi (kg/cm
2
)
max.
42 Basic Motor Design 3 phase
wye
connected 2(P/2)
43 Stator Phase Sequence A-C-B (viewed from front face plate)
44 Vendor/Supplier Industrial Drives B-202-B
45 Resolver Type/Accuracy Single-Speed; Rotor-Excited; ± 10 arc min.;
Resolution is 4096 counts/rev post-quadrature
46 Resolver Manufacturer/Model # Fasco # 21-BRCX-335-J39
47 Standard Resolver Cable Part Number 71-011777-xx
48 Standard Motor Cable Part Number 71-011774-xx
49 Options: Brake—24VDC (0.57A)—845 oz-in (5.97 Nm) Holding Torque (requires resolver
IP67 Classification No Keyway cable 71-014082-xx)
Incremental Encoder Shaft Modifications
Tachometer IP65 Shaft Seal
[1] 25°C (77°F) Ambient
[2] 40°C (104°F) Ambient
[3] Measured at 60 rpm (1 rps) in Velocity Mode
[4] Rated for 20,000 Hours or 40,000 Hours
@ 155° C (311°F)
[5] Rotor steel is rated as
fatigue proof
[6] Loads centered 1 inch from mounting flange
[7] Loads may be radial and axial such that the sum of the
radial and two times the axial does not exceed this figure.
[8] Motor shaft is IP30 rated.
APEX603 Motor Specifications
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...
Need help?
General
