Need help?Do you have a question about the PEUGEOT Ludix 4T and is the answer not in the manual?
Symbols for health and material hazards like irritation, flammability, and corrosivity.
Symbols for explosive, environmental, and toxicity hazards.
Symbols for recyclability and mandatory protective gear like gloves.
Symbols indicating personal danger or hazards to the vehicle.
Symbols for notes, lubrication, greasing, and using new parts.
Details on engine type, cooling, bore, capacity, power, torque, and lubrication.
Specifications for relay box, crankcase, and fuel tank capacities.
Details on chassis type, front, and rear suspension systems.
Overall length, width, height, wheelbase, and unladen weight.
Information on wheel rims, tyre sizes, and pressure specifications.
Details on front brake type, disc size, rear brake type, and lining thickness.
List of items to be checked during regular service intervals.
Estimated time in hours for various maintenance codes.
Procedure for preparing a new battery, excluding maintenance-free types.
Initial checks and setup procedures for a new scooter.
Specifies recommended unleaded fuel and safety precautions for fuel handling.
Specifies tightening torques for various engine parts.
Specifies tightening torques for body panels and cycle parts.
Specifies tightening torques for standard nuts and bolts by diameter.
Lists specific tools with part numbers and designations for specialized tasks.
Lists common tools and equipment needed for maintenance procedures.
Identifies locations of CDI unit, battery, magneto, fuse, HT coil, and regulator.
Identifies locations of starter relay, switches, horn, starter resistor, and warming units.
Step-by-step instructions for removing the front shield panel.
Step-by-step instructions for removing the rear shield panel.
Procedure for removing the footboard and side fairings.
Steps for removing the under body panel.
Instructions for removing the fuel tank, including saddle and luggage carrier.
Steps for removing the front and rear handlebar fairing covers.
Procedure for draining and refilling engine oil, including filter cleaning.
Steps for draining and refilling the gearbox oil in the relay box.
Procedure for removing, cleaning, and installing the air filter and its housing.
Steps for removing, checking, and installing the spark plug.
Procedure for removing the transmission cover and related components.
Procedure for checking and servicing the drive pulley and its components.
Method for measuring the drive belt width and checking for cracks.
Method for measuring the clutch lining thickness.
Steps for replacing the clutch lining assembly using specialized tools.
Instructions for installing and checking valve clearances.
Procedure for setting the engine idle speed to the correct RPM.
Steps for removing and replacing the fuel filter.
Procedure for checking front brake pad wear and minimum thickness.
Steps for removing and refitting brake pads, including piston actuation.
Instructions for checking and topping up the brake fluid level.
Procedure for checking wear marks and replacing rear brake linings.
Procedure for removing the front fork assembly.
Steps for replacing the steering head cups and bearings.
Method for correctly tightening the steering system components.
Steps for removing and refitting wheel bearings, using new bearings.
Diagram of the ignition principle and carburetor heater circuit.
Steps for checking the carburetor heating resistor and related components.
Procedures for checking the ignition system components and wiring.
Procedures for checking the starter motor relay and resistance.
Procedures for checking the high tension coil.
Procedures for checking the vacuum-operated cock and fuel reserve contact.
Procedures for removing the carburettor and its choke assembly.
Steps for removing starter holder, throttle valve, and needle assembly.
Steps for removing float, needle valve, jets, and needle well.
Procedure for adjusting the mixture screw and checking its initial position.
Steps for removing pick-up pump parts and carburetor heater.
Procedure for removing the deceleration enrichment device and checking its membrane.
Steps for cleaning the carburetor body and reassembling components.
Diagram showing all components of the carburettor for reassembly reference.
Steps to disconnect battery, magneto, starter, choke, heater, fuel lines, and throttle.
Procedures for disconnecting pulsair hose, brake cable, and linkrod.
Steps for removing the shock absorber mount and lifting the power unit from the frame.
To Next Page
General