WINDSHIELD WIPER OPERATION
Intermittent Wipers
The intermittent feature of this system was designed for
use when weather conditions make a single wiping
cycle, with a variable pause between cycles, desirable.
For maximum delay between cycles, rotate the control
knob upward to the first detent.
The delay interval decreases as you rotate the knob
until it enters the low continual speed position. The
delay can be regulated from a maximum of about
18 seconds between cycles, to a cycle every one sec-
ond. The delay intervals will double in duration when
the vehicle speed is 10 mph (16 km/h) or less.
Windshield Washers
To use the windshield washer, push the washer knob,
located on the end of the multifunction lever, inward
and hold. Washer fluid will be sprayed and the wipers
will operate for two to three cycles after the washer
knob is released.
If the washer knob is pushed while in the delay range,
the wipers will operate for several seconds after the
washer knob is released. The wipers will then resume
the intermittent interval previously selected. If the
washer knob is pushed while in the off position, the
wipers will turn on and cycle approximately three times
after the washer knob is released.
To prevent freeze-up of your windshield washer system
in cold weather, select a solution or mixture that meets
or exceeds the temperature range of your climate. This
rating information can be found on most washer fluid
containers.
WARNING!
Sudden loss of visibility through the windshield could
lead to a collision. You might not see other vehicles or
other obstacles. To avoid sudden icing of the wind-
shield during freezing weather, warm the windshield
with the defroster before and during windshield
washer use.
Mist
When a single wipe to clear off road mist or spray from
a passing vehicle is needed, push the washer knob,
located on the end of the multifunction lever, inward
briefly and release. The wipers will cycle one time and
automatically shut off.
NOTE:
The mist feature does not activate the washer pump;
therefore, no washer fluid will be sprayed on the wind-
shield. The washer function must be used in order to
spray the windshield with washer fluid.
For information on wiper care and replacement, see
page 271.
RAIN SENSING WIPERS —
IF EQUIPPED
This feature senses rain or snowfall on the windshield
and automatically activates the wipers. Rotate the end
of the multifunction lever to one of five detent positions
to activate this feature.
The sensitivity of the system can be adjusted with the mul-
tifunction lever. Wiper delay position 1 is the least sensi-
tive, and wiper delay position 5 is the most sensitive. Posi-
tion 3 should be used for normal rain conditions.
Positions 1 and 2 can be used if the driver desires less
wiper sensitivity. Positions 4 and 5 can be used if the
driver desires more sensitivity. Place the wiper switch in
the O (off) position when not using the system.
NOTE:
•
The Rain Sensing feature will not operate when the
wiper switch is in the low or high-speed position.
•
The Rain Sensing feature may not function properly
when ice, or dried salt water is present on the
windshield.
•
Use of products containing wax or silicone may
reduce Rain Sensing performance.
•
The Rain Sensing feature can be turned on and off
using the Uconnect system
page 174.
The Rain Sensing system has protection features for
the wiper blades and arms, and will not operate under
the following conditions:
•
Low Ambient Temperature — When the ignition is
first placed in the ON position, the Rain Sensing
system will not operate until the wiper switch is
moved, vehicle speed is greater than 0 mph
(0 km/h), or the outside temperature is greater than
32°F (0°C).
•
Transmission In NEUTRAL Position — When the igni-
tion is ON, and the transmission is in the NEUTRAL
position, the Rain Sensing system will not operate
until the wiper switch is moved, vehicle speed is
greater than 5 mph (8 km/h), or the gear selector is
moved out of the NEUTRAL position.
•
Remote Start Mode Inhibit — On vehicles equipped
with the Remote Start system, Rain Sensing wipers
are not operational when the vehicle is in the
Remote Start mode. Once the operator is in the
vehicle and has placed the ignition switch in the
GETTING TO KNOW YOUR VEHICLE 47
2
To Next Page
Loading...
