What does PSI Error Code 101 mean on my Raven Water Pump?
If your Raven Water Pump is displaying PSI Error Code 101, it indicates that the transducer is out of calibration or is faulty. You should recalibrate the pressure transducer. If the problem persists, replace the pressure transducer.
What to do if low tank volume remaining in Raven Farm Equipment?
If the tank volume is low, refill the product to continue field applications.
What could be the reason for Code 105 on my Raven Water Pump?
If your Raven Water Pump shows Code 105, it might be caused by a flow obstruction in the left exhaust valve or a faulty left pressure transducer. Perform a pump calibration test. If the pump does not calibrate properly, remove the left exhaust cartridge and perform pump maintenance to clear obstructions. If the pump calibrates properly, replace the left pressure transducer.
What to do if Raven Farm Equipment target flow is too high?
If the target flow is too high: 1. Reduce the equipment speed. 2. Reduce the target application rate.
What to do if injection pressure sensor disconnected in Raven Sidekick Pro Farm Equipment?
If the injection pressure sensor is disconnected: 1. Verify a good connection to the pressure sensor on the pump. 2. Verify the sensor is getting supply voltage. 3. Verify the signal voltage is getting back to the pump ECU.
What to do if Raven Farm Equipment displays a Low Pressure Alarm?
If you encounter a 'Low Pressure Alarm' on your Raven Farm Equipment, it means the injection pressure is lower than the carrier pressure. To resolve this, perform a pump calibration test; if it fails, clean the injection pump's inlet and discharge valves. Also, calibrate the pump transducer, check the lines between the injection pump and in-line mixer, ensure all hand valves are correctly positioned, and, if necessary, replace the pump transducer.
What does HC Power Alarm mean on Raven Sidekick Pro?
If you're seeing an 'HC Power Alarm' on your Raven Farm Equipment, the injection node is not connected to high current power. Verify that the high current breaker is not tripped and check the battery connections.
What does Motor/Encoder Code 105 mean on my Raven Water Pump?
If your Raven Water Pump is displaying error code 105 related to the motor or encoder, it may be due to no power to the pump motor or a pump motor/encoder issue. First, verify that the high current LED on the injection pump node is lit. Then, check the motor and encoder connections, ensuring they are properly seated. If the connections appear solid, return the pump to a local Raven dealer for service.
What does Code 110 mean on my Raven Water Pump?
If your Raven Water Pump is showing error Code 110, it may be due to no power to the pump motor or a pump motor/encoder issue. First, verify that the high current LED on the injection pump node is lit. Then, check the motor and encoder connections, ensuring they are properly seated. If the connections appear solid, return the pump to a local Raven dealer for service.
Why is my Raven Water Pump showing Code 107?
If your Raven Water Pump displays Code 107, it could be due to a clogged pump strainer, restrictions in tubing or plumbing, or the chemical being too thick. Clean the pump strainer and check for obstructions in the injection line. Verify the correct size of injection supply tubing is used. If the chemical is too thick, dilute it in the chemical supply tank, as some chemicals are not suitable for direct injection systems.
Guidelines for safe handling and application of agricultural chemicals.
Precautions for safe electrical connections and system operation.
Instructions for safely routing electrical harnesses on the machine.
Instructions for safely routing fluid carrying hoses on the machine.
Describes the purpose and function of the Raven Sidekick Pro injection system.
Lists the main components that make up the injection system.
Lists essential components and tools needed for system installation.
Information on software/documentation updates and providing feedback.
Steps to prepare the machine and system before physical installation.
Detailed steps for installing the pump and fill station components.
Instructions for mounting tank support brackets to the machine.
Steps for installing the chemical mixer and its associated plumbing.
Guide for connecting and routing electrical harnesses and components.
Instructions for applying operational decals to system components.
Explains how to operate the valves for chemical tanks.
Describes how to operate the fill station valves.
Details on operating single and dual pump valves.
Instructions for operating recirculation valves for single and dual pumps.
Initial configuration of the Raven OS and system sections.
Details on Product, Injection, Pressure, Section, and Alarm settings tabs.
Procedures for priming and calibrating the Sidekick Pro injection pump.
Process for re-addressing rate controllers on the CAN bus.
Configuring the display to match system settings and equipment.
Configuration of alarm settings for the sprayer or floater control system.
Procedure to calibrate all pressure transducers in the sprayer control system.
Procedure for remote closed-system calibration of the injection pump.
Interpreting LED status indicators on the Sidekick Pro motor control node.
Lists common error codes, their possible causes, and solutions.
List of part numbers for pumps, switches, sensors, and cables.
List of part numbers for mixers, tanks, valves, strainers, and fittings.
Part numbers for support brackets, templates, and operation labels.
Diagram showing electrical connections and component layout.
Diagram illustrating the fluid path and component connections.
General| Category | Farm Equipment |
|---|---|
| ISOBUS Compatibility | Yes |
| Display | Touchscreen |
| Connectivity | Wi-Fi, Bluetooth |
| Battery Life | Up to 10 hours |
To Next Page
