Raven Sidekick Pro - User Manual

Other manuals for Raven Sidekick Pro

Installation & Operation Manual86 pages

Quick Installation Reference26 pages

Questions and Answers

T
Teresa YoungSep 5, 2025
What to do if Raven Laboratory Equipment displays DI high vacuum error?
- C
  codymaddoxSep 5, 2025
  If the Raven Laboratory Equipment is showing a DI high vacuum error, follow these steps: 1. Disconnect the vacuum switch from the product cable and test for continuity between pins A and C. If the OHM meter reads a short, the switch is good. If it reads open, the vacuum switch is bad. 2. Check for obstructions from the inlet of the tank. Look for debris in the inlet, a plugged filter/strainer, a hand valve turned in the wrong direction, or an obstruction in the outlet of the chemical tank.
C
christine97Sep 6, 2025
How to troubleshoot low pump efficiency in Raven Laboratory Equipment?
- U
  uavilaSep 6, 2025
  To troubleshoot low pump efficiency in Raven Laboratory Equipment, check for the following: * Fouled pump check valves * Air leaks on the injection pump inlet plumbing * Air in the chemical * Plugged inlet strainer * Chemical too thick to flow through the pump Additionally, calculate the volume per minute for the application and verify the rate is within the range of the injection pump. Finally, check the flow monitor sensor.
C
Catherine RaymondSep 6, 2025
How to fix security failure on Raven Laboratory Equipment?
- D
  Deborah AlvarezSep 7, 2025
  To resolve a security failure on Raven Laboratory Equipment, cycle the device power.

Raven Sidekick Pro Specifications

General

Category	Farm Equipment
ISOBUS Compatibility	Yes
Display	Touchscreen
Connectivity	Wi-Fi, Bluetooth
Battery Life	Up to 10 hours

Summary

Important Safety Information

Agricultural Chemical Safety

Guidelines for safe handling and application of agricultural chemicals.

Electrical Safety

Precautions for safe electrical connections and system operation.

Wire Routing Guidelines

Instructions for safely routing electrical harnesses on the machine.

Hose Routing Guidelines

Instructions for safely routing fluid carrying hoses on the machine.

Introduction to Sidekick Pro System

System Overview

Describes the purpose and function of the Raven Sidekick Pro injection system.

Injection System Components

Lists the main components that make up the injection system.

Required Components and Tools

Lists essential components and tools needed for system installation.

Updates and Feedback

Information on software/documentation updates and providing feedback.

Installation Procedures

Installation Preparation

Steps to prepare the machine and system before physical installation.

Pump and Fill Station Installation

Detailed steps for installing the pump and fill station components.

Tank Support Bracket Installation

Instructions for mounting tank support brackets to the machine.

Mixer Installation

Steps for installing the chemical mixer and its associated plumbing.

Electrical Components Installation

Guide for connecting and routing electrical harnesses and components.

Decal Placement

Instructions for applying operational decals to system components.

Valve Operation

Tank Valve Operation

Explains how to operate the valves for chemical tanks.

Fill Station Operation

Describes how to operate the fill station valves.

Pump Valve Operation

Details on operating single and dual pump valves.

Recirculation Valve Operation

Instructions for operating recirculation valves for single and dual pumps.

Viper 4 (ROS) Initial Set-Up

Raven OS and Section Setup

Initial configuration of the Raven OS and system sections.

System Configuration Tabs

Details on Product, Injection, Pressure, Section, and Alarm settings tabs.

Sidekick Pro Pump Priming and Calibration

Procedures for priming and calibrating the Sidekick Pro injection pump.

CNH Pro 700 Set-Up

Re-Addressing Rate Controllers

Process for re-addressing rate controllers on the CAN bus.

Product Controller Set-Up

Configuring the display to match system settings and equipment.

Alarms Set-Up

Configuration of alarm settings for the sprayer or floater control system.

Pressure Transducer Calibration

Procedure to calibrate all pressure transducers in the sprayer control system.

Injection Pump Calibration

Procedure for remote closed-system calibration of the injection pump.

Troubleshooting

Motor Control Node LED Status Indicators

Interpreting LED status indicators on the Sidekick Pro motor control node.

Sidekick Pro Error Codes and Alarms

Lists common error codes, their possible causes, and solutions.

Replacement Parts

Pumps and Cabling Parts

List of part numbers for pumps, switches, sensors, and cables.

Plumbing Parts List

List of part numbers for mixers, tanks, valves, strainers, and fittings.

Support Brackets and Labels

Part numbers for support brackets, templates, and operation labels.

System Diagrams

Electrical System Diagram

Diagram showing electrical connections and component layout.

Plumbing System Diagram

Diagram illustrating the fluid path and component connections.

Limited Warranty Information

Extended Warranty Information

Related product manuals

Raven SmarTrax

156 pages

Raven SmarTrax Spra-Coupe 220

12 pages

SBG Slingshot Field Hub 2.0

Raven AccuFlow Vortex

98 pages

Raven Case IH AutoBoom XRT