Record DFA127 - Page 103

To Previous Page

Subject to technical modications – Copyright

agtatec ag

n°102-127108955 – Manufacturer: agtatec ag – Allmendstrasse 24 – 8320 Fehraltorf – Switzerland

Contact

your global partner for entrance solutions

record your global partner for entrance solutions

Î Manufacturer

agta record ltd – Allmendstrasse 24 – 8320 Fehraltorf – Switzerland

tel. +41 44 954 91 91 – info@agta-record.com

Distribution / Service Hotline:

Main Page

Table of Contents2
General8
Product Identification8
- Manufacturer Agtatec Ag8
- Document Identification8
Important Information DFA 1278
- Copyright8
Target Group9
Storage of the Manual9
Description of the Equipment9
Low Energy Drive (Low Energy)9
Types of Arms, Including Accessories9
Accessories and Special Applications for the DFA 12710
Safety Instructions11
Presentation of Warning Signs11
- General Safety and Accident Prevention Regulations11
Product Safety13
State of the Technology13
Intended Use13
Danger Zones13
Security- and Surveillance Equipment13
Danger Warnings on the Product13
Qualifications, Skills and Training of Staff13
Reconstructions and Changes to the Product13
Security Inspection According en 1600514
Swing Doorsets14
Protection During Opening and Closing Cycles14
Monitored Zones at the Primary Closing Edge15
Protective Measures at Secondary Closing Edge (Hinges)16
Safety Distances17
Safety Distances in the Detection Field (with Radar Motion Sensor)17
Low-Energy Movements for Swing Door Drive17
General and Additional Requirements18
Detection Zone for Sensor Activation18
Additional Requirements18
Additional Requirements for Doorsets in Escape Routes and Emergency Exits19
Marking of Glass19
Guards19
Commissioning and Information for Use19
Technical Data DFA 12720
Door Leaf Weights and Door Widths20
Instructions for Low Energy Operators (Low-Energy)21
Generally Authorised Speed Settings22
Construction and Function23
Construction23
Functions23
Types of Arms24
Standard Arm24
Slide Arm Pulling24
Slide Arm Pushing24
Lever Adapters for Arms25
Standard Arm25
Slide Arms Pulling and Pushing25
Skirt Ring as Reinforcement26
Demounting the Lever Adapter26
Installation Plan for Arm Systems27
Standard Arm (Pushing)27
Installation of Operator on Door Leaf27
Slide Arm Pulling28
Slide Arm Pushing28
Profiles for Operator Height 85 or 108 MM29
Chassis 85 MM29
Chassis 108 MM29
Casings 85 or 108 MM29
Assembly Dimension Diagrams30
Dimension Diagram 1 for Standard Arms30
Dimension Diagram 2 for Standard Arms31
Dimension Diagram 1 for Slide Arm, Pulling and Pushing32
Dimension Diagram 2 for Slide Arm, Pulling and Pushing33
- Installation DFA 12734
Checking the Installation Site34
Positioning the DFA and Arm34
Mechanical Installation of the DFA34
- Adjustment of the Initial Spring Tension According en 4 to en37
Checking the Mechanical Functions38
- Control Unit STG 12738
Preparation39
Connecting the Sensors, Electrical Door Openers39
Checking the Settings39
Connection of Safety Sensors40
Wiring40
Linkage Rod Adjustment Possibilities42
Angle Adjustment42
Length Adjustment43
- Commissioning DFA 12744
Principles of Commissioning44
Requirements of the Technician44
Mechanical Final Test44
Wiring Control44
Checking Safety Devices44
The CAN-Bus45
The Bus Topology45
The Correct Cable47
The CAN Connector47
Addressing Bus Components48
Changing Addresses49
Deactivating / Reactivating Bus Components (Replacing Faulty Sensors)49
Simplified Start-Up50
Checking the Leds on the STG53
Checking the BDE Functions and Actuation Devices53
Programming Door Speeds and Hold-Open Times53
Configuration of Specific Customer Settings53
Safety Check53
Checking Automatic Reverse53
Touch Control (Push to Actuate)53
Checking the Functions of the DFA53
Hand over to the Client53
- Operating Instructions DFA 12754
- Controls of the STG 12754
Electronic Controller BDE-D (Option)55
Adressing of the Electronic Controller55
Operating Modes and Behaviour of the Door During Input Signals56
Mech. Control Elements and Indication58
Mechanical BDI (Control Toggle Switch)58
Reset-Button59
Statusanzeige59
Configurations60
Parameter Description60
Description of Parameters61
Special Remarks80
Function Chart81
Connection of a Time Switch for "Locked" (SUR-V)81
Master / Slave Application82
Use82
Functions82
Distinctive Features83
Interlock Mode with 2 Single-Leaf Doors84
- Single Doors, Connection with CAN-Isolator84
Putting into Operation the Interlock Mode84
Functions of the Electronic BDE-D in Interlock Mode84
- Single Doors, Communication with FEM85
Configuration85
Interlock Control (Basic Wiring Required)85
Deactivation of the Interlock Mode86
Interlock Sequence Control86
Options86
Lamp87
Accessories88
Gearbox Cover with Position Switch88
Extended Function Module FEM 189
Status and Fault Signals90
Detail Description of Status Indications90
Maintenance Instructions92
Verifications for a New Assembly93
Specification for Fire Doors94
Operator Types94
Arm Types94
Settings to Adjust Closing Time94
Parameter Setting for Utilisation on Fire Doors95
Hints for Low-Energy Operators95
Ü-Designation95
Hold-Open System for Bi-Parting Doors (Master / Slave)95
Acceptance of Hold-Open System95
Abbreviations DFA96
- Drawings98
- Wiring Diagram100

Record DFA127 - Page 103

Table of Contents

Related product manuals