112
Sampling procedure
1.
Press [PATCH/SAMPLE] to enter Patch/Sample mode.
2.
Press SAMPLING [START/STOP].
The sampling menu screen will appear.
fig.07-001
3.
Use the VALUE dial or [INC] [DEC] to select the desired
sampling method.
4.
Press [ENTER].
The sampling-standby screen will appear.
fig.07-002
5.
Make the settings for things such as the input source of the
sound to be sampled, and triggering.
Use [CURSOR ] to select a parameter, and turn the
VALUE dial or use [INC] [DEC] to set the value.
Sampling Sample the sound from the external in-
put.
* The internal sound generator won’t pro-
duce sound even if you operate the key-
board pads, D Beam, or sequencer.
Resampling
Sample the sound from the internal
sound generator.
* [MIX IN] will be off.
There will be no sound from the external
input source.
Mix
(Mix sampling)
Sample the sound of the internal sound
generator mixed with the sound from the
external input source.
Auto Divide
(Auto divide
sampling)
Sample a long (extended duration)
source while automatically dividing it
into multiple samples at regions of si-
lence.
* The internal sound generator won’t pro-
duce sound even if you operate the key-
board pads, D Beam, or sequencer.
Solo
(Solo sampling)
Sample only the external input source
while you listen to the internal sound
generator as usual.
At the same time that sampling begins,
the currently selected pattern will begin
playing. Use this when you want to sam-
ple from an external source while listen-
ing to the pattern playback.
* You won’t be able to apply an effect to the
sound of the external input source.
Solo with FX
(Solo with FX
sampling)
This is essentially the same as Solo Sam-
pling.
An effect can be applied to the sound of
the external input source.
* Make the desired effect settings before you
begin sampling (p. 61).
Parameter
Range Description
Input
LINE IN L/R
,
LINE IN L,
MICRO-
PHONE
Input source to be sampled
LINE IN L/R:
INPUT jacks
L/R (stereo)
LINE IN L:
INPUT jack L
(mono)
MICROPHONE:
INPUT
jack L (mono, mic level)
* This cannot be set when re-
sampling.
Stereo Switch
MONO,
STEREO
Stereo/mono setting for
sampling
MONO:
The sound will be
sampled as one wave. If the
sound is stereo, the left and
right signals will be mixed.
STEREO:
The sound will
be sampled as two waves,
L and R.
* Mono sampling uses half
as much memory space.
Pre Sample
(Pre Sample
Time)
0–1000 ms The length of sound pre-
ceding the moment at
which sampling was man-
ually or automatically initi-
ated that will be captured
in the sample
This lets you prevent the
attack portion of the
sound from being omit-
ted from the sample.
Stop Trigger MANUAL,
BEAT,
TIME
How sampling will end
MANUAL:
Continue sam
-
pling until you press
[START/STOP].
BEAT:
Sample the speci-
fied number of beats at the
current tempo (BPM).
TIME:
Sample the speci-
fied length of time.
Sampling Len
(Sampling
Length)
When Stop Trigger is BEAT
1–20000
Number of beats to contin-
ue sampling
When Stop Trigger is TIME
00'01–50'00
Length of time to continue
sampling
The maximum value will depend on the
amount of memory.
* This parameter cannot be specified if Stop
Trigger is set to MANUAL.
Auto Trigger
Sw
(Auto Trigger
Switch)
OFF,
ON
If this is on, sampling will
begin automatically when
the input sound is detected.
* Pressing [START/STOP]
won’t start sampling.
Auto Trigger
Level
0–7
Volume level at which
sampling will begin when
Auto Trig is ON
A setting of 0 is the min-
imum.
MC-808_r_e.book 112 ページ ２００７年７月１７日 火曜日 午後５時１分
To Next Page
Loading...
