Sennheiser SpeechLine - Installing antenna splitters in a rack

214 pages

Save Page as PDF

To Next Page

To Previous Page

The SL PASC 4 passive antenna splitter/combiner

211

Installing antenna splitters in a rack

This chapter describes how to install a single antenna splitter

or two antenna splitters side by side in a rack.

GA 4 mounting kit

To install the antenna splitter in a rack, you need the GA 4

mounting kit.

The GA 4 mounting kit consists of:

►

Main Page

SpeechLine Digital Wireless: System Information2
Focus on the spoken word4
- SpeechLine Digital Wireless – the professional solution for speakers, lecturers and presenters5
- Typical applications6
- What are the features of SpeechLine Digital Wireless?9
The Products of the SpeechLine Digital Wireless Series13
- The SL Rack Receiver DW receiver13
- SL Multi-Channel Receiver DW15
- The handheld transmitter17
- The bodypack transmitter18
- The wireless SL Tablestand 133-S DW19
- The wireless SL Tablestand 153-S DW20
- The wireless SL Boundary 114-S DW21
- The CHG 2 charger22
- The CHG 4N charger23
- The CHG 2W charging base24
Accessories25
- The clip-on and headset microphones25
- The AWM 2 antenna wall mount26
- The AWM 4 antenna wall mount27
- The SL PASC 2 passive antenna splitter28
- The SL PASC 4 passive antenna splitter29
- Antenna cables30
SpeechLine Digital Wireless: System planning31
Planning33
- Country-Specific Variants33
- Number and size of the rooms35
- Shared use of the 1.9 GHZ frequency band36
- Analysis of the environmental conditions38
Recommendations on antenna mounting39
- Antenna setup and planning for SpeechLine Digital Wireless39
- Antenna mounting options40
- Option 1: Connecting the AWM 2 or AWM 4 antenna wall mount directly to the receiver(s)41
- Option 2: Combining multiple links to one AWM 2/AWM 444
- Option 3: Rack mounting - front48
- Option 4: Rack mounting - rear49
- Further important information on antenna usage50
Multi-room mode52
SpeechLine Digital Wireless: Instruction manual60
SL Rack Receiver DW63
- Product overview and operating elements – front panel64
- Product overview and connections – rear panel67
- Connecting the receiver68
- Controlling and monitoring the receiver via the network70
- Updating the firmware74
- Setting up the receiver75
- Installing receivers in a rack78
- Displays on the receiver’s display panel83
- Using the operating menu of the receiver86
SL MCR DW93
- Product overview and operating elements94
- Directivity of the integrated antennas95
- Connecting the receiver97
- Mounting the receiver101
- Putting the receiver into operation108
- Controlling and monitoring the receiver via the network108
- Meaning of the status LEDs110
- Updating the firmware112
The SL Handheld DW113
- Product overview114
- Displays on the display panel of the SL Handheld DW117
- Starting up and using the handheld transmitter117
- Updating the firmware122
The SL Bodypack DW123
- Product overview124
- Displays on the display panel of the SL Bodypack DW127
- Starting up and using the bodypack transmitter128
- Updating the firmware132
The SL Tablestand 133-S DW133
- Product overview134
- Starting up and using the table stand135
- Updating the firmware141
The SL Tablestand 153-S DW142
- Product overview143
- Starting up and using the table stand144
- Updating the firmware150
The SL Boundary 114-S DW151
- Product overview152
- Starting up and using the boundary microphone153
- Updating the firmware157
Pairing158
- Identifying paired devices159
- Pairing a receiver with a transmitter161
Performing a walk test (reception quality)165
The SL Headmic 1 headset microphone169
- Preparing the SL Headmic 1 for use169
- Changing the microphone position (left/right)170
- Adjusting the microphone boom and the neckband172
- Using the frequency response caps174
- Using the windshield175
- Attaching the connection cable to clothing175
- Connecting the SL Headmic 1 to the SL Bodypack DW176
The MKE 1 clip-on microphone177
- Treble boost178
- Attaching the microphone178
- Connecting the MKE 1 to the SL Bodypack DW179
The CHG 2 charger180
- Product overview180
- Connecting the CHG 2 charger to the power supply system181
- Charging the accupack in the CHG 2 charger182
The CHG 4N charger183
- Product overview184
- Connecting the CHG 4N charger to the power supply system185
- Charging the accupack in the CHG 4N charger187
- Meaning of the charging slot status LEDs188
- Controlling and monitoring the CHG 4N charger over the network190
- Updating the firmware193
The CHG 2W charging base194
- Product overview194
- Connecting the CHG 2W charging base to the power supply system195
- Charging a device using the CHG 2W charging base196
- Meaning of the status LEDs on the charging surfaces197
The AWM 2 antenna wall mount198
- Product overview199
- Connecting and mounting the AWM 2201
The AWM 4 antenna wall mount205
- Product overview206
- Connecting and mounting the AWM 4207
The SL PASC 2 passive antenna splitter/ combiner210
- Connectors on the rear of the device210
The SL PASC 4 passive antenna splitter/ combiner211
- Connectors on the rear of the device211
- Installing antenna splitters in a rack212

Sennheiser SpeechLine - Installing antenna splitters in a rack

Table of Contents

Other manuals for Sennheiser SpeechLine

Related product manuals