Shihlin electric SS2 Series User Manual

Contents
contents
5.26 The Choice of Locking Operation Keyboard Knob Setting (P.59) ........................................................................ 94
5.27 Input Signal Filter Constant (P.60) .......................................................................................................................... 94
5.28 Remote Control Function Selection (P.61) .............................................................................................................. 95
5.29 Zero Current Detection (P.62, P.63) ......................................................................................................................... 97
5.30 Retry (P.65, P.67, P.68, P.69) ..................................................................................................................................... 97
5.31 Brake Selection (P.71) ............................................................................................................................................... 98
5.32 Carrier Frequency (P.72) .......................................................................................................................................... 99
5.33 Stop or Reset Function Selection (P.75
）
.............................................................................................................. 100
5.34 Parameters Write Protection (P.77) ....................................................................................................................... 101
5.35 Forward/Reverse Rotation Prevention Selection (P.78) ....................................................................................... 101
5.36 Operation Mode Selection (P.79) ............................................................................................................................ 101
5.37 Multi-function Terminals Function Selection (P.80~P.84, P.86) .......................................................................... 102
5.38 Multi-Function Control-Terminal Input Positive/Negative Logic (P.87) ............................................................ 107
5.39 Multi-Function Output Terminal Positive/Negative Logic(P.88)......................................................................... 108
5.40 Slip Compensation Coefficient (P.89) V/F ........................................................................................................ 108
5.41 The Inverter Model (P.90)....................................................................................................................................... 108
5.42 Frequency Jump (P.91~P.96) .................................................................................................................................. 109
5.43 The Second Frequency Source
（
P.97
）
................................................................................................................ 110
5.44 Programmed Operation Mode (P.100~P.108, P.111~P.118, P.121~P.123, P.131~P.138) ...................................... 110
5.45 Operation Panel Monitoring Selection (P.110) ...................................................................................................... 113
5.46 The selection of positive and reverse rotation dead time (P.119) ......................................................................... 113
5.47 Zero-speed Function (P.151~P.152) V/F ......................................................................................................... 114
5.48 Over Torque Detection (P.155~P.156, P.260) ......................................................................................................... 114
5.49 External Terminals Filter Adjusting Function (P.157) ......................................................................................... 115
5.50 External Terminal Power Enable Function (P.158) .............................................................................................. 116
5.51 Energy-saving Control Function (P.159) V/F ................................................................................................. 116
5.52 Multi-function Display (P.161) ............................................................................................................................... 116
5.53 PID Control (P.170~P.183, P.223~P.225) ................................................................................................................ 117
5.54 4-5 Terminal Disconnection Handling (P.184) ...................................................................................................... 122
5.55 Proportion Linkage Function
（
P.185
）
................................................................................................................ 122
5.56 Firmware version (P.188) ........................................................................................................................................ 123
5.57 Factory Setting Function (P.189) ............................................................................................................................ 124
5.58 Input Signal across Terminal 2-5 (P.192~P.195).................................................................................................... 125
5.59 Input Signal across Terminal 4-5 (P.196~P.199).................................................................................................... 126
5.60 The Paver Function (P.226~P.228) ......................................................................................................................... 127
5.61 Backlash Compensation and Acceleration/Deceleration Interrupted for Waiting Function (P.229~P.233)
V/F .................................................................................................................................................................................... 128
5.62 Triangular Wave Function (P.234~P.239) V/F .................................................................................................. 130
5.63 Auxiliary Frequency Function (P.240) ................................................................................................................... 131
5.64 DC Injection Brake Function before Starting (P.242~P.244) V/F................................................................... 131
5.65 Options for Stopping the Cooling Fan (P.245) ...................................................................................................... 132
5.66 Commercial Power Supply Frequency Operation Function (P.247~P.250) V/F ........................................... 133
5.67 Maintenance Alarm Function (P.261) .................................................................................................................... 136
5.68 Vibration Inhibition Factor (P.286) ....................................................................................................................... 136

Shihlin electric SS2 Series Specifications

General

Brand	Shihlin electric
Model	SS2 Series
Category	Inverter
Language	English