Pos: 127 /100 Sigm a/100 BA Ze ntrifugen Sigma ( Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol L (Z ent6)/060- 0030-0020 M anueller Betri eb @ 27\mod_ 14053192541 92_68.docx @ 192647 @ 3 @ 1
→
6.3.2 Manual mode
Pos: 128 /100 Sigm a/100 BA Ze ntrifugen Sigma ( Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol L (Z ent6)/060- 0030-0020- 0010 Starten ei ner Zentrifugati on @ 27\mod _1405319255424 _68.docx @ 192661 @ 4 @ 1
→
6.3.2.1 Starting a centrifugation run
The centrifuge is ready for operation when the start key is illuminated.
• Press the start key in order to start a centrifugation run.
Pos: 129 /010 Univ ersalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 130 /100 Sigm a/100 BA Ze ntrifugen Sigma ( Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol L (Z ent6)/060- 0030-0020- 0020 Unterbrec hen einer Zentri fugation @ 27 \mod_1405319 256724_68.doc x @ 192675 @ 4 @ 1
→
6.3.2.2 Interrupting a centrifugation run
• Press the stop key in order to interrupt a centrifugation run. The
centrifugation run will be terminated prematurely.
Quick stop
• Press the stop key for more than two seconds.
The centrifuge decelerates with the maximum deceleration curve.
After a quick stop, the centrifuge lid must be opened before a new
centrifugation run can be started.
A quick stop can also be triggered during a normal deceleration, e.g. in
order to speed up the deceleration.
When a quick stop is triggered, “fast” will be displayed in the lower right-
hand corner of the display.
Pos: 131 /010 Univ ersalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 132 /100 Sigm a/100 BA Ze ntrifugen Sigma (Standardm odule)/060 Betr ieb_Spincontrol L+S/Spinco ntrol L (Zent6)/060- 0030-0020- 0030 Unterbrec hen eines Brems vorgangs @ 2 7\mod_140531 9258018_68.d ocx @ 1926 89 @ 4 @ 1
→
6.3.2.3 Interrupting a deceleration process
• Press the start key during a deceleration process in order to interrupt it
and to restart the centrifuge.
Pos: 133 /010 Univ ersalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 134 /100 Sigm a/100 BA Ze ntrifugen Sigma ( Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol L (Z ent6)/060- 0030-0020- 0040 Auswahl, A nzeige und Än derung von Dat en @ 27\mod _14053192593 17_68.docx @ 192703 @ 4 @ 1
→
6.3.2.4 Selection, display, and modification of data
• Turn the function knob in order to select a field. The selected field will
be preceded by the indication "set", "run", or "save".
• Press the function knob. The indication ("set", "run", or "save") flashes
and the modification mode is active.
• Turn the function knob in order to modify the set value of the selected
field.
• Press the function knob again to confirm the input and to quit the
modification mode
• The process will be interrupted if the stop key is pressed or after 60
seconds without any further input.
Pos: 135 /010 Univ ersalmodule/ Seitenwechs el @ 0\mo d_120211624 4312_0.docx @ 105 @ @ 1
To Next Page
Loading...
Need help?
General
