Simplex 4010 Service Manual

IN-2
isolator bases
and IDNet channel failure trouble, 2-8
and no answer trouble, 2-9
K
known solutions, C-11
L
LCD Annunciator
disabling piezo, C-9
LCD display trouble
for LCD card, 2-15
LCD membrane trouble
for LCD card, 2-15
LCD troubles
LCD display trouble, 2-15
LCD membrane trouble, 2-15
missing card trouble, 2-15
wrong card trouble, 2-15
link scan/code scan loop, 1-2, 1-3
M
MAPNET II ZAM
and no answer trouble, 2-9
missing card trouble
and RS-232/modem card, 2-11
for 24 point I/O card, 2-14
for LCD card, 2-15
for NAC card, 2-2
for power supply card, 2-4
for SDACT card, 2-12
N
N2 comm diagnostics, C-2
NAC
determining current draw, 2-3
troubles for NAC 3 or 4, 2-3
NAC circuit trouble
troubleshooting for, 2-2
NAC signal power trouble, 2-3
NAC troubles
Class A, 2-2
missing card, 2-2
NAC circuit trouble, 2-2
signal power, 2-2
wrong card, 2-2
network. see diagnostics, network diagnostics
network card troubles
duplicate node trouble, 2-13
ground fault troubles, 2-13
missing card trouble, 2-13
net comm failure trouble, 2-13
network miswire, 2-13
version mismatch trouble, 2-13
wrong card trouble, 2-13
network diagnostics, C-5
O
output devices
problems with supervisory point type, C-11
P
PCC chip
and channel failure trouble, 2-8
piezo
disabling on LCD Annunciator,C-9
Port A/B disconnected trouble, 2-11
power supply troubles, 2-4
AC power trouble, 2-4
battery charger trouble, 2-7
battery depleted/disconnected trouble, 2-6
battery low cutout trouble, 2-6
battery low trouble, 2-6
Earth ground troubles, 2-5
EPS battery trouble, 2-5
EPS trouble, 2-4
missing card trouble, 2-4
wrong card trouble, 2-4
power up flow charts
initial startup sequence, 1-2
power up flowcharts
overview of, 1-1
printer
troubleshooting, 2-11
program checksum trouble
for SDACT card, 2-12
programming
restoring default, C-9
R
remote LED
problems with, C-11
revision levels
and boot software, 1-3
RS-232/modem card
does not come on-line, 2-11
missing card trouble, 2-11
Port A/B disconnected trouble, 2-11
wrong card trouble, 2-11
S
SDACT conversion errors, 11
SDACT download problems, 11
SDACT troubles
central station trouble, 2-12
DB version mismatch trouble, 2-12
missing card trouble, 2-12
phone line 1 or 2 trouble, 2-12
program checksum trouble, 2-12
wrong card trouble, 2-12
serial devices
troubleshooting, 2-11
SFIO board
features for different revisions, A-2
supervisory point type, C-11
system reset
and Class A trouble, C-12
lengthening reset timer, C-12
T
trouble messages
NAC troubles, 2-2
TrueAlarm isolator devices, 1-3
Technical Manuals Online! - http://www.tech-man.com

Simplex 4010 Specifications

General

Display	LCD
Power Supply	120/240 VAC, 50/60 Hz
Manufacturer	Simplex
Model	4010
Battery Backup	24 VDC
NAC Outputs	4
Max Detectors	250
Max Modules	250
Operating Temperature	0°C to 49°C (32°F to 120°F)
Humidity Range	Up to 93% RH, non-condensing