Skyjack SJ82 T - How to Unlock and Modify SCM Settings

171
SJ82 T, SJ86 T
229040ABA
Platform Section 5 – Procedures
5.2-7 How to Unlock and Modify SCM Settings
MODE= XX/XX STD
FUNCTIONS OFF
UNLOCK SETUP?
PRESS SELECT
(FLASHING)
SAVE
▬▬▬▬
EXIT
SOFTWARE REVISION
MODEL SERIAL NUMBER
STARTING
SCREEN
ENTER PASSWORD
0**
0 (FLASHING)
SET DRIVE TIMER
PRESS SELECT
(FLASHING)
MODE: XXXXX
FUNCTIONS OFF
DISPLAYED
Increases
V
alue
TOGGLE
ADJUST
(FLASHING)
(DRIVE REV) THRESH
Fn01A VALUE= %
(FLASHING)
ENTER PASSWORD
7**
7 (FLASHING)
ENTER PASSWORD
70*
0 (FLASHING)
ENTER PASSWORD
75*
5 (FLASHING)
ENTER PASSWORD
750
0 (FLASHING)
ENTER PASSWORD
755
5 (FLASHING)
SETUP UNLOCKED
PRESS - OR +
(
FLASHING
)
(DRIVE FWD) THRESH
Fn01B VALUE= %
(FLASHING)
+ (BOOM DOWN) THRESH Fn03A VALUE= %
THRESH Fn03B VALUE= %
THRESH Fn04A VALUE= %
THRESH Fn04B VALUE= %
+ (JIB FLOW) THRESH Fn05A VALUE= %
+ (PLAT FLOW) THRESH Fn05B VALUE= %
THRESH Fn06A VALUE= %
THRESH Fn06B VALUE= %
(
FLASHING
)
XXXX XX (THRESH)
Fn0XX VALUE= %
(FLASHING)
MODE= XX/XX LTD
FUNCTIONS OFF
XXXX XX
(THRESH/MAXOUT/
LOWRNG/RAMPUP/RAMPDN)
Fn0XX VALUE= %
(FLASHING)
XXXX XX (XXXXXX)
Fn0XX VALUE = % or SEC
(FLASHING)
Decreases
Value
ONCE THE VALUE HAS
BEEN ADJUSTED WITHIN
THE PARAMETER OF THE
FUNCTION SELECTED,
YOU MAY CONTINUE TO
ANOTHER ADJUSTABLE
PARAMETER OR SAVE/
EXIT ALL THE WAY OUT
TO THE START SCREEN
MENU
▬▬▬▬
SELECT
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
▲
▬▬▬
┼
5X
5X
7X
MENU
▬▬▬▬
SELECT
MENU
▬▬▬▬
SELECT
MENU
▬▬▬▬
SELECT
MENU
▬▬▬▬
SELECT
SAVE
▬▬▬▬
EXIT
MENU
▬▬▬▬
SELECT
MENU
▬▬▬▬
SELECT
MENU
▬▬▬▬
SELECT
TOGGLE
▬
▬▬▬
▼
▲
▬▬▬
┼
▲
▬▬▬
┼
CE Models
ANSI/CSA
Models
OR
▬
▬▬▬
▼
+ (DRIVE FWD)
+ (ROTATE L)
+ (ROTATE R)
+ (BOOM UP)
+ (FLY OUT)
+ (FLY IN)
+ (LR REV)
+ (LR FWD)
(DRIVE REV)
THRESH Fn01A VALUE= %
THRESH Fn01B VALUE= %
THRESH Fn02A VALUE= %
THRESH Fn02B VALUE= %
Recycle power to the SCM with the E-Stop to re-enable password protection.
If the SCM is inactive for more than 5 minutes, password must be re-entered.
To order go to Discount-Equipment.com