Option
menu
parameter
of
2/zone
3
operations
2.
Whcn
the reccivcr
in
the main zonc and
zone
2
arc turncd
ofT.
you can select a radio station from
AM
or
FM
in
zone 3.
Whcn two
of
the receivers
in
thc main ?One.
zone
2
or
zone 3 are turned
ofT.
you can selecl a
broadcast
from
FM/AM/XM/SIRIUS
in
one
zone
in
which
the rcceiver is turned on.
RM-AAL008
IR
repeater
(nol supplied)
STR-DA5300ES
About the
IR
REMOTE jack
vou
can
operate the receiver without pointing
the
remote toward the IR repeater
of
the
receiver
if
you connect
an
IR repeater (not
supplied) to
the
IR
REMOTE
jack.
Usc
an
IR repeater when you install the
receiver in a place where signals from the
remote cannot reach.
• RS-232C Control
•
ON
The receiver
can
receive commands from the
RS-232C port.
• OFF
The receiver
does
not receive commands
from the RS-232C port.
Tips
o Even when this receiver is standby
mode
(press
I/C)
on the remote to turned
off
this receiver). the
receiver
in
zone
2
or
zonc
3 rcmains turned on. To
turn
off
all receivers. press
I/C)
and
AV
I/C)
on the
RM-AALOOR remote at
the
same
time
(SYSTEM
STANDBY).
o
Only
signals from
components
connccted
to the
analog
input
jacks
are output through the
ZONE
2
OUT/ZONE
3
OUT
jacks.
No
signals are
output
from
components
connccted
to only the digital
input
jacks.
•
Whcn
SOURCE
is selcctcd. the signals input to thc
MULTI
CHANNEL
INPUT
jacks
are
not output
from the
ZONE
2
OUT
or
ZONE
3
OUT
jacks
evcn when the multi-channel input
is
selected.
Thc
analog
audio
signals
of
the currcnt function are
outpul.
•
Whcn
"Tuncr"
is selcctcd; the
samc
Iypc
of
radio
station
(FM/AM)
selected
in
the
main
zone
is
SCI
in
zone
2 and
zone
3. However.
you
can
select the
input
othcrthan
"Tuner"
in
zone
2 and
zone
3.
o
When
the
rcceiver
in
thc main ?Onc
is
turncd ofr.
or
an input source
othcr
than
"Tuner"
is
selected. you
can select a radio station from AM
or
FM
in
zone
• 12V Trigger
Vou
can
turn the receiver
on/off
in another
zone, or select various options for
usc
of
the
12V Trigger function.
as
explained below.
• OFF
Lets you turn
off
output
of
12V triggers
even
when
the
main receiver
is
turned on.
•
ZONE
Lets you turn the output
of
12V triggers
on
or
off
based
on
whether
the
selected zone
is
turned
on
or
otT.
o
CTRL
Lets you turn
the
output
of
12V triggers
on
or
off
manually using the CIS command
of
the
IR remote.
•
INPUT
(for
"Main"
only)
Lets you turn
on
the output
of
12V triggers
when
the
preset input
is
selected.
When you select
"Input,"
the
setting display
which
sets
each
input trigger to
on/off
appears.
Press
+/+ to select the input. then
press
8)
to check the box.
•
MAIN
(for
"Zone
2'"
and
"Zone 3" only)
Lets you link operation
of
trigger in zone 2
or zone
:1
to the main receiver.
112
GB
To Next Page
Loading...
