Synrad Firestar f series - Page 133

index
i1
Synrad Firestar f-Series operator’s manual
Symbols
+24 VDC Auxiliary Power 3-11, 3-20, 3-22,
3-24
pin description, 3-11, 3-14
+5 VDC Auxiliary Power 3-11, 3-20, 3-24,
4-15, 4-16
pin description, 3-11, 3-14
A
Agency compliance. See Compliance
American National Standards institute (ANSI)
2, 3
Analog current control 3-8–3-9
Analog voltage control 3-8–3-9
Aperture. See Laser aperture
Aperture seal 2-2, 2-4, 2-7, 2-9
Applications xi
Assist gas 4-19
purity specication 3-5
Auxiliary DC power
+24 VDC, 3-11, 3-14, 3-20, 3-24
+5 VDC, 3-11, 3-14, 3-20, 3-24, 4-15,
4-16
Aux. DC Power Ground, 3-12, 3-14, 3-24,
4-15, 4-16
internal wiring diagram, 3-14
pin descriptions, 3-14
Auxiliary DC Power Ground 3-11, 3-12, 3-24,
4-15, 4-16
signal description, 3-14
B
Base plate 1-10, 1-11, 1-12, 1-13
Beam attenuator 8, 11
Beam block 3, 2-7, 2-8, 2-9, 2-11, 4-6
Beam characteristics 3-3
Beam delivery optics 3-4
caution, 3-5, 4-2, 4-3, 4-18
radiation danger, 4-4, 4-18
troubleshooting, 4-17–4-19
Beam diameter 3-3
specications, 3-28, 3-30, 3-32, 3-34
Bend radius 1-21, 1-22, 3-25
Block diagram 4-8
BNC Control cable 1-7, 1-9
connecting, 1-26
C
Caution
code requirements, 1-23, 1-24
condensation damage, 1-18, 1-20, 2-7,
2-8, 2-9, 2-11
cooling ttings, 1-15, 1-18, 1-19
denition, 1
dirty/dusty environments, 3-3, 3-5, 4-2,
4-3, 4-18
laser damage, 1-17, 1-21
mounting, 1-10
optics damage, 3-3, 3-5, 4-3
purge pressure, 1-28, 2-7, 2-10
reverse polarity, 1-21
User I/O connector, 1-27, 3-13
voiding warranty, 4-6
Center for Devices and Radiological Health
(CDRH) 8–9
Class 4 safety features, 11
CE mark 13
label location, 4, 6
Chiller
connection, 1-18, 1-19–1-20
coolants, 1-16
ttings, 1-7, 1-9, 1-15, 1-16
ow rate, 1-16, 1-19, 1-20, 4-15
preparation, 1-16
temperature setpoint, 1-16, 1-17, 1-19,
1-20, 2-7, 2-9, 4-15
Chiller ttings 1-7, 1-9, 1-16
Class 4 safety requirements 11
Cleaning optical components 4-3–4-5
Code of Federal Regulations (CFR) 2, 8, 9
Collimators 3-4
Command signal 3-7–3-8
base frequency, 3-7
PWM duty cycle, 3-8
signal amplitude, 3-7
signal specications, 3-8
Compliance 8–13