Need help?Do you have a question about the Teac A-3340 and is the answer not in the manual?
Mechanical specifications for TEAC A-3300 and A-3340 models.
Electrical specifications for the TEAC A-3300 model.
Electrical specifications for the TEAC A-3340 model.
Tools and equipment needed for mechanical measurements.
Tools and equipment needed for electrical measurements.
Procedure for removing the rear panel and wooden sides.
Procedure for removing the bottom plate.
Procedure to replace the entire head assembly.
Procedure to replace individual tape heads.
Steps to remove the capstan motor and assembly.
Steps to remove the reel motor assembly.
Removal of tension arms.
Alignment procedure for the erase head pole.
Alignment procedure for the record head pole.
Alignment procedure for the playback head pole.
Steps to change the operating voltage.
Steps to change the operating frequency.
Torque specifications for A-3300-10 and A-3300-12.
Torque specifications for A-3340 and A-3300-11.
Procedure to check and adjust take-up torque.
Procedure to check and adjust back tension.
Procedure to adjust reel height.
Flutter specifications and measurement guidelines.
Tape speed specifications and measurement guidelines.
Important notes before performing electrical adjustments.
Procedure for coarse and fine adjustment of playback head azimuth.
Procedure to set the specified output level.
Measuring and adjusting frequency response.
Procedure to adjust minimum input levels.
Procedure to set specified input levels.
Procedure to adjust the bias trap circuit.
Bias adjustment for the normal position.
Bias adjustment for the high position.
Procedure for coarse adjustment of record head azimuth.
Procedure for fine adjustment of record head azimuth.
Procedure to set specified output level for A-3340.
Calibrate VU meter during playback for A-3340.
Procedure to adjust minimum input levels for monitor.
Procedure to set specified input levels for monitor.
Procedure to adjust bias trap circuit for recording.
Bias adjustment for normal position.
Bias adjustment for high position.
Frequency response check with bias switch in normal position.
Frequency response check with bias switch in high position.
Procedure for cleaning tape path components.
Procedure for demagnetizing parts and heads.
Lubrication points and procedure.
Ventilation and overheating precautions.
Guide to common malfunctions, sources, and corrective procedures.
Exploded view and parts list for trim parts.
Exploded view and parts list for control panel.
Exploded view and parts list for reel motor assembly.
Exploded view and parts list for capstan drive assembly.
Exploded view and parts list for lifter and pinch roller.
Exploded view and parts list for head assembly.
Head configurations for A-3300/A-3340 models.
Exploded view and parts list for right tension arm.
Exploded view and parts list for left tension arm.
Exploded view and parts list for main chassis.
Exploded view and parts list for rear panel.
Parts list for MIC and Playback EQ Amplifier.
PC board and schematic for MIC/Playback EQ Amplifier.
Parts list for Line Out and Phone Amplifier.
PC board and schematic for Line Out/Phone Amplifier.
Parts list for Meter and Rec. EG. Amplifier.
PC board and schematic for Meter/Rec. EQ. Amplifier.
PC board layout for Control Relay.
PC board layout and parts list for Rectifier.
PC board layout and parts list for Start Motor.
Exploded view and parts list for A-3340 head assembly.
Head configurations for A-3300/A-3340 models.
Exploded view and parts list for A-3340 preamplifier chassis.
Continued parts list for A-3340 preamplifier chassis.
Details about adding a DIN connector.
Details about revisions to the rear cover assembly.
Details about revisions to the recording relay circuit.
Details about changes to the pilot light assembly.
Schematic diagram for the tape transport.
Schematic diagram for the head assembly.
Schematics for A-3300-10,12 and A-3300-11 models.
To Next Page
General
