Toro Multi Pro 1750 - Calibrating the Sprayer Speed; Calibrating the Section-Bypass Valves

2.Usingtheplus(+)andminus(-)symbols,enter
theowvolumeaccordingtothetablethat
follows:
NozzleColor
Liters
USGallons
Yellow4211
Red8322
Brown10628
Gray
12533
White16744
Blue208
55
Green
31483
3.Turnonthemaster-sectionswitchfor5minutes.
Note:Asthemachinesprays,theInfoCenter
displaysthequantityofuidthatitiscounting.
4.Afterthe5minutedurationofsprayingclickthe
checkmarkbypressingthecenterbuttononthe
InfoCenter.
Note:Itisacceptableifthegallonsdisplayed
duringthecalibrationprocessdonotmatch
theknownquantityofwaterenteredintothe
InfoCenter.
5.After5minutes,turnoffthemaster-section
switchandselectthecheckmarkonthe
InfoCenter.
Note:Calibrationisnowcomplete.
CalibratingtheSprayer
Speed
Beforeusingthesprayerforthersttime,ifyou
changethenozzles,orasneeded,calibratethe
sprayerspeed.
1.Fillthetankwithfreshwater.
2.Onanopen,atarea,markoffadistance
between45to152m(150to500ft).
Note:Tororecommendsmarkingoff152m
(500ft)formoreaccurateresults.
3.Starttheengineanddrivetothestartofthe
marked-offdistance.
Note:Alignthecenterofthefronttireswiththe
startinglineforthemostaccuratemeasurement.
4.OntheInfoCenter,navigatetotheCalibration
menuandselectSPEEDCAL.
Note:SelectingtheHomeScreeniconatany
timecancelscalibrations.
5.SelecttheNextarrow(→)ontheInfoCenter.
6.Usingtheplus(+)andminus(-)symbols,enter
themarked-offdistanceintotheInfoCenter.
7.Shiftthemachineintorstgearanddrivethe
markeddistanceinastraightlineatfullthrottle.
8.Stopthemachineatthemarked-offdistance
andselectthecheckmarkontheInfoCenter.
Note:Slowdownandrolltoastoptoalignthe
centerofthefronttireswiththenishline,for
themostaccuratemeasurement.
Note:Calibrationisnowcomplete.
Calibratingthe
Section-BypassValves
Beforeusingthesprayerforthersttime,ifyou
changethenozzles,orasneeded,calibratethe
sprayersectionbypass
Important:Selectanopenatareatoperform
thisprocedure.
PreparingtoCalibratethe
Section-BypassValves
1.Fillthespraytankhalfwaywithcleanwater.
2.Lowerthesprayersections.
3.MovetherangeselectortotheNEUTRALposition
andsettheparkingbrake.
4.Setthe3sectionswitchestotheONposition,
butleavethemaster-sectionswitchoff.
5.SetthepumpswitchtotheONposition,andturn
ontheagitation.
6.Pressdownontheacceleratorpedaluntilyou
reachthemaximumenginespeed,andtoggle
thethrottlelockswitchtotheONposition.
7.OntheInfoCenter,navigatetotheCalibration
menuandselectTESTSPEED.
Note:SelectingtheHomeScreeniconatany
timecancelsthecalibration.
8.Usingtheplus(+)andminus(-)symbols,enter
atestspeedof5.6km/h(3.5mph),thenselect
theHomeicon.
9.Turnthesupervisor(rate-lockout)switchtothe
UNLOCKposition,andturnthemaster-section
switchtotheONposition.
31