RTHD-SVX01L-EN
51
Controls
Overview
Optimus™ Model RTHD units utilize the following control/
interface components:
• Symbio™ 800 Controller
• Tracer AdaptiView™ TD7 Operator Interface
Symbio™ 800
The Symbio™ 800 controller is a factory-installed,
application specific and programmable controller designed
to control chillers and large packaged HVAC equipment. A
7 inch user interface features a touch-sensitive color
screen that provides facility managers at-a-glance
operating status, performance monitoring, scheduling
changes, and operating adjustments. Other advanced
features include automated controller back-up, and
optional features such as secure remote connectivity,
wireless building communications, mobile device
connectivity, and custom programming with an expandable
I/O.
For more information, see Symbio™ 800 Controller
Installation, Operation, and Maintenance Manual (BAS-
SVX080*-EN)..
AdaptiView™ Display
Information is tailored to operators, service technicians,
and owners. When operating a chiller, specific information
is needed on a day-to-day basis—setpoints, limits,
diagnostic information, and reports. This information is
provided through the AdaptiView™ display. Logically
organized groups of information— chiller modes of
operation, active diagnostics, settings and reports put
information conveniently at your fingertips.
For more information, see User Guide, RLC-SVU008*-EN,
Optimus™ Water-Cooled Chillers AdaptiView™ Display
with Symbio™ Controls .
Tracer TU
The AdaptiView™ TD7 operator interface allows for daily
operational tasks and setpoint changes. However, to
adequately service chillers, Tracer® TU service tool is
required. (Non-Trane personnel, contact your local Trane
office for software purchase information.) Tracer TU adds a
level of sophistication that improves service technician
effectiveness and minimizes chiller downtime. This
portable PC-based service-tool software supports service
and maintenance tasks, and is required for software
upgrades, configuration changes and major service tasks.
Tracer TU serves as a common interface to all Trane
chillers, and will customize itself based on the properties of
the chiller with which it is communicating. Thus, the service
technician learns only one service interface.
The panel bus is easy to troubleshoot using LED sensor
verification. Only the defective device is replaced. Tracer
TU can communicate with individual devices or groups of
devices.
All chiller status, machine configuration settings,
customizable limits, and up to 100 active or historic
diagnostics are displayed through the service-tool software
interface.
LEDs and their respective Tracer TU indicators visually
confirm the availability of each connected sensor, relay,
and actuator.
Tracer TU is designed to run on a customer’s laptop,
connected to the Tracer® Symbio™ 800 control panel with
a USB cable. Your laptop must meet the following
hardware and software requirements:
• 1 GB RAM (minimum)
• 1024 x 768 screen resolution
• CD-ROM drive
• Ethernet 10/100 LAN card
• An available USB 2.0 port
• Windows 7 Enterprise or Professional operating system
(32-bit or 64-bit)
Note: Tracer TU versions 8.6 and earlier will also
support Microsoft
®
Windows
®
XP Professional
operation system with Service Pack 3 (SP3) .
• Microsoft .NET Framework 4.0 or later.
Note: Tracer TU is designed and validated for this minimum
laptop configuration. Any variation from this
configuration may have different results. Therefore,
support for Tracer TU is limited to only those laptops
with the configuration previously specified.
Air-Fi® Wireless Communication
Interface (WCI Indoor)
Factory installed wireless interface provides wireless
communication to Air-Fi® wireless sensors, service tools,
equipment controls, and building controller.
Trane Wi-Fi Adapter
The Trane Wi-Fi adapter kit (equipped with a USB cable)
enables communication among devices on a Wi-Fi network
to facilitate the wireless integration of client devices such
as touch-screen displays and technician laptops as an
access point.
To Next Page
Loading...
