Tyco Galaxy SC Controller User Manual

Tyco Electronics Galaxy SC Controller J85501F-1
Issue 13 February 2001 Operation 6 - 23
The following example illustrates how to configure the connected
equipment ID:
CHA DS1,CID=“MCS”
This command identifies the connected equipment on data switch port 1
(DS1) as an MCS controller. For the other data switch ports substitute
DS2, DS3, or DS4 for DS1. It may also be necessary to change the
password used for the connected equipment. To do this, use the
following command substituting your password for “password”:
CHA DS1,PWD=“password”
To enter pass-thru mode set the data switch port using the following
command:
OPE DS1,STT=“PASS-THRU”
Alarm Reporting
Mode
Like pass-thru mode, for most applications, only the connected
equipment ID needs to be configured for reporting mode. To enter
reporting mode use the following command:
STA DS1,REN=1
If call out is required it will also be necessary to configure the connected
equipment alarm. The following examples illustrate how this can be
done for the connected equipment on data switch port 1:
CHA P2,PHN=“123-4567” configure call-out phone number 2
CHA CEA1,DES=“MCS Alarms”
configure the alarmdescription
CHA CEA1,DST=“P2” configure alarm call-out destination
to be P2
CHA CEA1,NOO=1 configure the alarm to notify on occur
The call-out destination phone number may require additional
configuration, see the section on call-out. For the other data switch ports
substitute CEA2, CEA3, or CEA4 for CEA1. To see if any data switch
connected equipment alarms are active use the following command:
ALA DSW

Tyco Galaxy SC Controller Specifications

General

Model	Galaxy SC
Power Supply/Operating voltage	12V DC
Inputs	8
Outputs	4
Type	Controller
Communication Interface	RS485

Summary

1 Introduction

The Product

Describes the Tyco Electronics Galaxy SC Controller, J85501F-1.

Customer Service Contacts

Provides contact information for customer service, training, and technical support.

2 Product Description

Overview

Introduces the Galaxy SC Controller's role in monitoring and controlling telecommunications power equipment.

Basic Controller

Explains the basic local control and monitoring functions of the battery plant.

Intelligent Controller

Details advanced control and monitoring features added by the intelligent controller option.

3 Installation

Overview

Outlines the installation process for new plants or replacing existing controllers.

Precautions

Lists safety precautions to consider before performing installation procedures.

New Plant Installation

Instructions for installing a Galaxy SC shipped directly from the factory in a new Battery Plant.

4 Configuration

Introduction

Outlines the initial plant power-up and required controller configuration.

Methods of Configuring Galaxy

Covers configuration via front panel, remote terminal (T1.317), and EasyView software.

Basic Controller Configuration From the Front Panel

Explains how to configure plant attributes using the front panel interface.

5 Acceptance Testing

Introduction

Explains testing procedures to simulate alarm conditions and verify controller functions.

Tools and Test Equipment

Lists the necessary tools for performing acceptance tests.

Precautions

Lists safety steps to follow when testing plant alarms.

6 Operation

Introduction

Details operating the Galaxy SC Controller from front panel, EasyView, or T1.317.

Basic Controller’s Front Panel Operation

Depicts front panel displays and operational paths.

Alarm Cut Off

Explains how to perform ACO operation to temporarily disable audible alarms.

7 Feature Descriptions

AC Distribution

Supports monitoring of AC distribution parameters via T1.317 or front panel.

Alarm Cut-Off (ACO)

Provides means for temporarily disabling audible alarm contacts.

Alarm Test

Provides means to sequentially assert user selected contact relays for testing.

8 Troubleshooting

Introduction

Describes troubleshooting procedures requiring circuit pack removal/replacement.

Basic Controller Circuit Packs

Discusses troubleshooting for BJB Microprocessor Board and other basic boards.

Intelligent Controller Circuit Packs

Discusses troubleshooting for BJH Microprocessor Board and BJJ Power Board.

9 Safety

Safety Statements

Read and follow all safety instructions and warnings before installation, maintenance, or repair.

Warning Statements and Safety Symbols

Explains symbols and statements for hazardous conditions.

Precautions

Lists precautions for working on or using this type of equipment.

10 Product Warranty

A. Seller warrants to Customer only, that:

Seller warrants products will be free from defects and conform to specifications.

B. The Warranty Period listed below is applicable to Seller’s Manufactured Products

Lists warranty periods for new and repaired products.

Appendix A T1.317 Interface

Overview

Describes T1.317 as the primary source of access to Galaxy SC Controller features.

Login

Explains how a user can login to the T1.317 interface.

Objects and Attributes

Explains T1.317 standard organizes system into objects and attributes.

Appendix B T1.317 Objects and Attributes

Table B-1: System Objects and Attributes

Lists system objects and their attributes.

Table B-2: DC Distribution Objects and Attributes

Lists DC distribution objects and their attributes.

Table B-3: AC Distribution Objects and Attributes

Lists AC distribution objects and their attributes.

Appendix C T1.317 Error Messages

Error Messages and Causes

Lists T1.317 interface error messages and their possible causes.

Syntax Related

Lists specific command syntax errors.

Security Related

Lists error messages related to security.

Appendix D TL1 (Transaction Language 1) and X.25 Interface

Introduction

Describes TL1 command interface for Galaxy SC Controller.

Equipment Setup and Installation

Describes wiring and configuring Galaxy SC for TL1.

Galaxy Unit Setup

Enables TL1 function by setting BJH DIP switch.

Appendix E Terminal Menu Interface

Login

User enters text-based terminal menu interface by logging into T1.317.

Menus

Lists available menus for checking system status, history, and statistics.

Appendix F Spare Parts

Table F-1: Spare Parts

Lists spare parts available for Galaxy SC Controller Model J85501F-1.

Appendix G Glossary

Alarm Severity

Defines severity levels for alarms: critical, major, minor, warning, record only.

Critical Alarms

Indicates severe, service-affecting conditions requiring immediate action.

Major Alarms

Indicates serious disruption of service or failure of important circuits.