Home
Vacon
Media Converter
NXP
Vacon NXP User Manual
4
of 1
of 1 rating
94 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
8 • vacon
connection of signals between maste
r and follower
Tel. +358 (0)201 2121 • Fax +358 (0)201 2
12 205
3
3.
CONNECTION OF SIGNALS BETWEEN MASTER AND FOLLOWER DRIVE (OPT-A7)
NOTE:
To eliminate the risk of electrical noise, use only double shielded twisted pair
cable for
connections.
7
9
Table of Contents
Default Chapter
3
Table of Contents
3
1 Introduction
5
Requirements
6
Trial Time Period
6
2 Control I/O
7
3 Connection of Signals between Master and Follower Drive (OPT-A7)
8
4 Jumper Setting on the OPT-A7 Board
9
5 Terminal to Function" (TTF) Programming Principle
10
Defining an Input/Output for a Certain Function on Keypad
10
Defining a Terminal for a Certain Function with Ncdrive Programming Tool
11
Defining Unused Inputs/Outputs
12
6 Shaft Synchronization Application - Parameter Lists
13
Monitoring Values (Control Keypad: Menu M1)
13
Basic Parameters (Control Keypad: Menu M2 G2.1)
14
Input Signals
15
Basic Settings (Control Keypad: Menu M2 6.3.2 G2.2.2)
15
G2.2.1)
15
Analogue Input
15
Analogue Input 2 (Control Keypad: Menu M2 G2.2.3)
16
Free Analogue Input, Signal Selection (Keypad: Menu M2 G2.2.4)
16
Digital Inputs (Control Keypad: Menu M2 G2.2.5)
17
Output Signals
18
Delayed Digital Output 1 (Keypad: Menu M2 G2.3.1)
18
Delayed Digital Output 2 (Keypad: Menu M2 G2.3.2)
18
Digital Output Signals (Control Keypad: Menu M2 G2.3.3)
19
Limit Settings (Control Keypad: Menu M2 G2.3.4)
20
Analogue Output 1 (Control Keypad: Menu M2 G2.3.5)
21
Analogue Output 2 (Control Keypad: Menu M2 G2.3.6)
21
Analogue Output 3 (Control Keypad: Menu M2 G2.3.7)
22
Mechanical Brake (Control Keypad: Menu M2 G2.3.8)
22
Drive Control Parameters (Control Keypad: Menu M2 G2.4)
23
Motor Control Parameters (Control Keypad: Menu M2 G2.5)
24
PMSM Settings (Control Keypad: Menu M2 G2.5.19)
25
Protections (Control Keypad: Menu M2 G2.6)
26
Fieldbus Parameters (Control Keypad: Menu M2 G2.7)
28
Torque Control Parameters (Control Keypad: Menu M2 G2.8)
29
Shaft Synchronization Parameters (Control Keypad: Menu M2 G2.9)
30
License Key (Control Keypad: Menu M2 G2.10)
31
Keypad Control (Control Keypad: Menu M3)
31
System Menu (Control Keypad: Menu M6)
31
Expander Boards (Control Keypad: Menu M7)
31
7 Description of Parameters
32
Vacon Shaft Synchronization Application
32
Keypad Control Parameters
85
Application Specific Variables in the Monitor Menu and Fieldbus Interface
86
8 Shaft Synchronization Operation
87
Shaft Synchronization Fieldbus Interface
90
9 Appendices
91
Closed Loop Parameters (ID's 612 to 621)
91
Note on Use of Permanent Magnet Motors ("AC Brushless" Motors)
91
Parameters of Motor Thermal Protection (ID's 704 to 708)
92
Parameters of Stall Protection (ID's 709 to 712)
92
Fieldbus Control Parameters (ID's 850 to 859)
92
10 Shaft Synchronization Application Specific Fault Codes
93
11 Commissioning of Shaft Synchronization Application
93
Other manuals for Vacon NXP
Hardware Manual
78 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Vacon NXP and is the answer not in the manual?
Ask a question
Vacon NXP Specifications
General
Brand
Vacon
Model
NXP
Category
Media Converter
Language
English
Related product manuals
Vacon nxs
165 pages
Vacon nxp/c
112 pages
Vacon NXP series
86 pages
Vacon CX
148 pages
Vacon CXL
27 pages
Vacon CXS
70 pages
Vacon NX
239 pages
Vacon NX series
122 pages
Vacon NXS series
86 pages
Vacon NXA series
122 pages
Vacon NX Active Front End
110 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
