Vanderbilt SPC6350 - Meaning of Written Warning Notices; Meaning of Hazard Symbols

To Next Page

To Previous Page

Security

Meaning of written warning notices

Vanderbilt

Installation & Configuration Manual

A6V10276959

01.05.2016

2.3 Meaning of written warning notices

Signal Word

Type of Risk

DANGER

Danger of death or severe bodily harm.

WARNING

Possible danger of death or severe bodily

harm.

CAUTION

Danger of minor bodily injury or property

damage

IMPORTANT

Danger of malfunctions

2.4 Meaning of hazard symbols

WARNING

Warning of hazard area

WARNING

Warning of dangerous electrical voltage

Main Page

Default Chapter3
- Table of Contents3
1 Meaning of Symbols11
2 Security12
- Target Group12
- General Safety Instructions12
- Meaning of Written Warning Notices14
- Meaning of Hazard Symbols14
3 Directives and Standards15
- EU Directives15
4 Technical Data31
- Spc400031
- Spc500032
- Spc600035
- Spcp355.30038
5 Introduction39
6 Mounting System Equipment40
- Mounting a G2 Housing40
- Mounting a G3 Housing41
  - Mounting a Back Tamper Kit43
  - Battery Installation for EN50131 Compliance47
- Mounting a G5 Housing48
- Mounting a Keypad54
- Mounting an Expander54
7 Smart PSU55
- SPCP355.300 Smart PSU55
8 Controller Hardware66
- Controller Hardware 42Xx\43Xx\53Xx\63Xx66
- Controller Hardware SPC5350 and 635069
9 Door Expander71
10 Wiring the System72
- Wiring the X-BUS Interface72
- Wiring of Branch Expander81
- Wiring the System Ground82
- Wiring the Relay Output82
- Wiring the Zone Inputs83
- Wiring an External SAB Bell86
- Wiring an Internal Sounder87
- Wiring Glassbreak87
- Installing Plug-In Modules87
11 Powering up the SPC Controller89
- Powering from Battery Only89
12 Keypad User Interface90
- Spck420/42190
- Spck620/62395
13 Software Support Tools101
14 Starting the System102
- Engineer Modes102
  - Engineer Pins102
- Programming Tools103
  - Fast Programmer103
- Configuring Start-Up Settings103
- Creating System Users105
- Programming the Portable ACE105
- Configuring Wireless Fob Devices106
  - Clearing Alerts Using the Fob107
15 Soft Engineer Programming Via the Keypad109
16 Engineer Programming Via the Keypad110
- System Status110
- Options111
- Timers114
- Areas116
- Area Groups117
- X-Bus118
  - X-BUS Addressing118
  - XBUS Refresh118
  - Reconfigure119
  - Keypads/Expanders/Door Controllers120
  - Locate120
  - Monitor120
  - Edit Keypads121
  - Edit Expanders123
  - Edit Door Controllers127
  - Addressing Mode128
  - XBUS Type129
  - Bus Retries129
  - Comms Timer129
- Wireless130
  - Add Sensors130
  - Edit Sensors (Zone Assignment)131
  - Add WPA131
  - Edit WPA132
- Zones132
- Doors133
- Outputs136
  - Outputs Types and Output Ports137
- Communication140
  - Serial Ports140
  - Ethernet Ports140
  - Modems141
  - Monitoring the Transmission Network Interface141
  - Configuring Modems142
  - Central Station143
  - Add143
  - Edit143
  - Delete144
  - Make Test Call144
  - Remote Maintenance144
- Test145
  - Bell Test145
  - Walk Test145
  - Zone Monitor145
  - Output Test146
  - Soak Test147
  - Audible Options147
  - Visual Indicators147
  - WPA Test148
  - Seismic Test148
- Utilities148
- Isolate149
- Event Log149
- Access Log150
- Alarm Log150
- Change Engineer Pin150
- Users150
  - Add151
  - Edit151
  - Access Control151
  - Delete153
- User Profiles154
  - Add154
  - Edit154
  - Delete154
- Sms155
  - Add155
  - Edit156
  - Delete156
- Set Date/Time157
- Installer Text157
- Door Control157
- SPC Connect158
17 Engineer Programming Via the Browser159
- System Information159
- Ethernet Interface159
- Connecting to the Panel Via USB161
- Logging into the Browser163
- SPC Home164
- Panel Status167
- Logs181
- Users183
- Configuration196
- Configuring Communications261
- File Operations304
- Using the Fast Programmer311
18 Accessing Web Server Remotely315
- PSTN Connection315
- GSM Connection317
19 Intruder Alarm Functionality320
- Financial Mode Operation320
- Commercial Mode Operation320
- Domestic Mode Operation321
- Full and Local Alarms321
20 System Examples and Scenarios322
- When to Use a Common Area322
21 Seismic Sensors324
- Seismic Sensor Testing325
22 Blocking Lock Operation328
- Blocking Lock328
- Authorized Setting of the Blocking Lock329
- Locking Element330
23 Appendix332
- Network Cable Connections332
- Controller Status Leds332
- Powering Expanders from the Auxiliary Power Terminals333
- Calculating the Battery Power Requirements334
- Domestic, Commercial and Financial Mode Default Settings336
- Wiring of the X10 Interface337
- SIA Codes337
- CID Codes342
- Overview of Keypad Types343
- User PIN Combinations344
- Duress Pins345
- Automatic Inhibits345
  - Zones345
  - Access Pins345
  - Engineer Access345
  - Keypad User Logoff345
- Wiring of Mains Cable to the Controller346
- Maintenance Controller346
- Maintenance Smart PSU347
- Zone Types347
- Zone Attributes350
- Applicable Attributes to Zone Types352
- ATS Levels and Attenuation Specifications354
- Supported Card Readers and Card Formats354
- SPC Support for E-Bus Devices356
  - Configuring and Addressing E-Bus Devices356
  - Addressing Transponders for SAP 8, SAP 14, and SAP 20358
  - Addressing Transponders for PSU SAP 25358
- Flexc Glossary359
- Flexc Commands360
- ATS Category Timings362
- ATP Category Timings363

Vanderbilt SPC6350 - Meaning of Written Warning Notices; Meaning of Hazard Symbols

Table of Contents

Related product manuals