Vitrek 952i - Page 132

95x Series Operating Manual - May 17, 2022
Page 132 of 155
Command
Description
DIO?,START
Responds with the <STRING> setting for the START DIO input
DIO,ABORT,<STRING>
Configures the ABORT DIO input to OFF, HI or LO
DIO?,ABORT
Responds with the <STRING> setting for the ABORT DIO input
DIO,INTERLOCK,<STRING>
Configures the INTERLOCK DIO input to OFF, HI or LO
DIO?,INTERLOCK
Responds with the <STRING> setting for the INTERLOCK DIO input
DIO,SEQUENCE,<STRING>
Configures the SEQUENCE DIO inputs to OFF, HI or LO
DIO?,SEQUENCE
Responds with the <STRING> setting for the SEQUENCE DIO inputs
DIO,PASS,<STRING>
Configures the PASS DIO output to HI or LO
DIO?,PASS
Responds with the <STRING> setting for the PASS DIO output
DIO,FAIL,<STRING>
Configures the FAIL DIO output to HI or LO
DIO?,FAIL
Responds with the <STRING> setting for the FAIL DIO output
DIO,TESTING,<STRING>
Configures the TESTING DIO output to HI or LO
DIO?,TESTING
Responds with the <STRING> setting for the TESTING DIO output
DIO,DWELL,<STRING>
Configures the DWELL DIO output to HI or LO
DIO?,DWELL
Responds with the <STRING> setting for the DWELL DIO output
DIO,HV,<STRING>
Configures the HV PRESENT DIO output to HI or LO
DIO?,HV
Responds with the <STRING> setting for the HV PRESENT DIO output
FAILARC,<BOOL>
Configures if the 95x is to fail on arc detection
FAILARC?
Responds with the <BOOL> fail on arc detection setting
FASTRERUN,<NR1>
Configures how a test sequence may be rerun from the front panel
0 – enable fast rerun
1 – enable fast rerun if pass
2 – disable fast rerun
FASTRERUN?
Responds with the <NR1> fast rerun setting
GATEWAY,<NR1>,<NR1>,<NR1>,<NR1>
Configures the Ethernet Gateway IP Address setting
GATEWAY?
Responds with the Ethernet Gateway IP address setting as four <NR1>
GPIB,<NR1>
Configures the GPIB address setting
GPIB?
Responds with the <NR1> GPIB address setting
HVSAFETY,<BOOL>
Configures the HV Detect safety feature
HVSAFETY?
Responds with the <BOOL> HV Detect safety feature setting
IP,<NR1>,<NR1>,<NR1>,<NR1>
Configures the Ethernet IP Address setting
IP?
Responds with the Ethernet IP address setting as four <NR1>
MAXDISCHARGE,<NR3>
Configures the maximum allowed discharge current during DCez, DCW
and DCIR type steps to the <NR3> value in amps, values between 1mA
and 200mA are valid
MAXDISCHARGE?
Responds with the <NR3> value of the maximum allowed discharge
current setting
MINLOAD,<BOOL>
Configures the enable for minimum loading detection during the ramp
period of DCW and DCIR steps -
0 or N – Minimum loading is not detected
1 or Y – Minimum loading is detected as configured in each individual
test step
MINLOAD?
Responds with the <BOOL> minimum loading detection enable setting
RS232,<NR1>
Configures the RS232 baud rate setting
RS232?
Responds with the <NR1> RS232 baud rate setting
SUBNET,<NR1>,<NR1>,<NR1>,<NR1>
Configures the Ethernet IP Subnet Mask setting
SUBNET?
Responds with the Ethernet IP Subnet Mask setting as four <NR1>