WinGD W-X82 - Page 79

Operation
0250−2/A1
Winterthur Gas & Diesel Ltd.
1/ 4
Alarms and Safeguards at Continuous Service Power
Media Unit Location Signal No.
(1)
Func-
tion
(2)
Type of
signal
(3)
Setting
value
[bar or _C]
Time
Interval
[sec]
Cylinder cooling water Pressure Engine inlet PT1101A ALM L 3.0 bar 0
SLD L 2.8 bar 60
PS1101S SHD L 2.5 bar 60
Temperature Engine inlet TE1111A ALM L
70_C
0
Outlet each cylinder TE1121−29A
ALM H
95_C
0
SLD H
97_C
60
LT circuit Pressure Cooler inlet PT1361A ALM L 2.0 bar 0
Single-stage SAC Fresh water Temperature Cooler inlet TE1371A ALM L
25_C
0
Cooler outlet TE1381−83A ALM H
80_C
0
HT circuit Pressure HT, Cooler inlet
PT1301A
ALM L 3.0 bar 0
two-stage SAC SLD L 2.5 bar 60
(for waste heat recovery) Temperature Cooler inlet
PT1331−32A
ALM H
120_C
0
SLD H
125_C
60
Lubricating oil Pressure Engine inlet PT2001A ALM L 3.8 bar 0
Bearing and piston cooling SLD L 3.6 bar 60
PS2002S SHD L 3.3 bar 10
Temperature Engine inlet TE2011A ALM H
50_C
0
SLD H
55_C
60
Temperature Bearing outlet TE2101−09A ALM H
65_C
0
SLD H
70_C
60
Servo oil Pressure Lubricating pump PT2041−42A ALM L
13)
40 bar 3
(for cylinder lubrication) Inlet FE/DE H 70 bar 3
Pressure Lubricating pump PT2046−47A ALM H 10 bar 0
(leakage) Inlet FE/DE
Servo oil Failure Automatic filter XS2053A ALM F − 0
Flow Servo oil pump FS2061−63A
11)
ALM L no flow 0
Oil leakage monitoring Level Supply unit
7)
LS2055A ALM H max. 0
Rail unit
7)
LS2076−77A ALM H max. 0
FE/DE
Thrust bearing oil Temperature Fore/aft side TE4521−22A ALM H
80_C
0
(thrust bearing pads) SLD H
85_C
60
Temperature Fore/aft side TE4526−27A ALM H
75_C
0
ASTERN SLD H
80_C
60
Temperature Fore side TS4521S SHD H
90_C
60
Temperature Aft side TS4522S SHD H
85_C
60
Crank bearing oil Temperature Outlet
TE2201−09A
ALM H
65_C
0
SLD H
70_C
60
Crosshead bearing oil Temperature Bearing outlet
TE2301−09A
ALM H
65_C
0
SLD H
70_C
60
Oil mist Concentration Crankcase AS2401−02A ALM H − 0
AS2401−02S SLD H − 60
Failure Detection unit XS2411−12A ALM F − 0
Piston cooling oil Temperature Outlet each cylinder TE2501−09A ALM H
80_C
0
SLD H
85_C
60
Diff. pressure Inlet each cylinder PS2541−49S SHD H 0.4 bar 15
Flow Inlet each cylinder FS2521−29S SHD L no flow 15
Operating Data Sheet
2017−04