WinGD WARTSILA RT-flex58T-D User Manual

Summary for Maintenance Manual
(MM)
Page No. Title Subject
Date No.
new exch.
2013 Issue 2013
x
Date of publication 2013-01-30
0380-1/A1 (2) 2013-02 TB RT-143 Maintenance Schedule 2728-1: Monthly check of nut to solenoid added x
2728-1/A1 Starting Air Valve
Check concerning venting of starting air manifold and
tightening of nut (18) to solenoild (17) added
x
2124-1/A1 Cylinder Liner x
2124-3/A1 (2) Cylinder Liner x
2708-1/A1 Cylinder Cover Cyliner liner with upper and lower water guide jacket adapted x
2722-1/A1 (6) Injection Valve Sec. 7: Remark added concerning replacing of a nozzle tip x
6420-1/A1 Scavenge Air Receiver Arrangement of air flaps standardized to those in OM x
9403-4/A1 (2) Hydr. Pre-tens. Jacks 1132-1: Comparison value in (°) deleted x
Date of publication 2013-02-20
0002-1/A1 x
Index 3, 9 x
0008-1/A1 (2) EAAD084591
Engine Numbering and
Designations
Crank angle sensor unit at gear wheel added x
0011-1/A1 (1)
Safety Measures and
Warnings
Attention concerning clean areas (no water or cleaning fluids)
added
x
0330-1/A1
(18, 19)
Clearance Table Key No. 6 and 7: points A and B added x
0380-1/A1 (2) Maintenance Schedule
3103-1: Interval changed "according to classification society"
x
(3)
3403-1: Intervals changed to 18 000-36 000 operating hours
3403-4: Intervals changed to 500-1000 operating hours
3425-1: Work to be carried out and intervals changed
x
2303-1/A1
(1, 7)
EAAD084619 Piston Rod Gland Recess applied on clamping ring 94345b as shown in Fig. 'G' x
2722-1/A1
(1, 3, 4-6, 8)
Injection Valve
Sec. 11 added; system oil as test media mentioned; Sec. 3:
keeping opening pressure changed from 10 to 30 seconds;
Sec. 5 revised; Remark concerning IMO technical file and
detail of nozzle type added
x
3103-1/A1
Measuring Crank
Deflection
1. General aspects; 2. Condition of measuring and 4. Crank
deflection limits revised
x
3425-1/A1
Piston Rings
(Four Piston Rings)
Determination of wear rate of chrome-ceramic piston rings and
measuring piston ring grooves introduced
x
3425-1/A2
Piston Rings
(Three Piston Rings)
Determination of wear rate of chrome-ceramic piston rings and
measuring piston ring grooves introduced
x
4103-3/A1 (5)
Replacing Gear Wheel
on Crankshaft
Stud side (thread) to be applied with MOLYKOTE and
LOCTITE 262 corrected
x
5801-1/A2 (1) Regulating Linkage
(with Woodward ProAct II Analog Actuator): 2nd sentence
about configuration and setting procedure added
x
8733-1/A1
(1, 2)
EAAD084136
HP Pipe to Injection
Valve
Special spanner 94874 and detail concerned in Fig. 'B' added x
9223-1/A2 2013 EAAD084591
Crank Angle Sensor
Unit
Assembly and replacement of proximity sensor (pickup) at
gear wheel introduced
x
9403-5/A1
(30, 33, 34)
2013-08 Tool List
Tools 94874, 94291A, 94356 (only figure modified) and 94357
added
x
Date of publication 2013-08-23
9403-5/A1
(3,4,10,21,26,
27,28,29,35)
2014-01 Tool List
94012 changed to 94012C, GF94020 changed to 94020D,
94022 changed to 94022B,94142 changed to 94142-L and -R,
94345F changed to 94345F/94345G,94651 changed to
94651C, 94662 deleted, 94481 deleted,94870E,F,G changed
to 94870K,94870A,B,C changed to 94870J
x
Modification Service
Engine Documentation
RT-flex58T-D Version 2
Supply Unit Aft End
Modification
Page or
2013-08
Table of Contents
3425-1/A1, A2: checking wear of … ring grooves and new
group 9223-1/A2 added
Execution cylinder liner / supporing ring replaced with cylinder
liner / water guide jacket
Manual
1/2 09/04/2018

WinGD WARTSILA RT-flex58T-D Specifications

General

Brand	WinGD
Model	WARTSILA RT-flex58T-D
Category	Engine
Language	English