Command Function Page
:SEARch<x>:CLOCk:POLarity
Sets the polarity of the clock channel or queries the current setting. 5-132
:SEARch<x>:CLOCk:SOURce
Sets the clock trace of the search or queries the current setting. 5-132
:SEARch<x>:DECimation
Sets the decimation detection of the skip mode or queries the current setting. 5-132
:SEARch<x>:EXECute
Executes the search. This is an overlap command. 5-133
:SEARch<x>:HOLDoff
Sets the hold off detection or queries the current setting. 5-133
:SEARch<x>:LOGic
Sets the search logic or queries the current setting. 5-133
:SEARch<x>:POLarity
Sets the search polarity or queries the current setting. 5-133
:SEARch<x>:SELect
Sets the detection waveform number of the search function and queries the
position that corresponds to the detection waveform number.
5-133
:SEARch<x>:SELect? MAXimum
Queries the detection count of the search function. 5-133
:SEARch<x>:SMODe
Sets the skip mode or queries the current setting. 5-133
:SEARch<x>:SPATtern? (Serial
Pattern)
Queries all settings related to the serial pattern search. 5-133
:SEARch<x>:SPATtern:CLOCk?
Queries all settings related to clock of the serial pattern search. 5-133
:SEARch<x>:SPATtern:CLOCk:MODE
Enables/Disables the clock of the serial pattern search or queries the current
setting.
5-134
:SEARch<x>:SPATtern:CLOCk:
POLarity
Sets the polarity of the clock trace of the serial pattern search or queries the
current setting.
5-134
:SEARch<x>:SPATtern:CLOCk:
SOURce
Sets the clock trace of the serial pattern search or queries the current setting. 5-134
:SEARch<x>:SPATtern:CS
Enables/Disables the chip select of the serial pattern search or queries the
current setting.
5-134
:SEARch<x>:SPATtern:LATCh?
Queries all settings related to latch of the serial pattern search. 5-134
:SEARch<x>:SPATtern:LATCh:
POLarity
Sets the polarity of the latch trace of the serial pattern search or queries the
current setting.
5-134
:SEARch<x>:SPATtern:LATCh:TRACe
Sets the latch trace of the serial pattern search or queries the current setting. 5-134
:SEARch<x>:SPATtern:SETup?
Queries all settings related to setup of the serial pattern search. 5-134
:SEARch<x>:SPATtern[:SETup]:
BITRate
Sets the bit rate of the serial pattern search or queries the current setting. 5-135
:SEARch<x>:SPATtern[:SETup]:
CLEar
Clears the entire pattern of the serial pattern search (to don’t care). 5-135
:SEARch<x>:SPATtern[:SETup]:
DATA?
Queries all settings related to data of the serial pattern search. 5-135
:SEARch<x>:SPATtern[:SETup]:
DATA:ACTive
Sets the active level of the data trace of the serial pattern search or queries
the current setting.
5-135
:SEARch<x>:SPATtern[:SETup]:
DATA:TRACe
Sets the data trace of the serial pattern search or queries the current setting. 5-135
:SEARch<x>:SPATtern[:SETup]:
HEXA
Sets the pattern of the serial pattern search in hexadecimal notation. 5-135
:SEARch<x>:SPATtern[:SETup]:
PATTern
Sets the pattern of the serial pattern search in binary notation or queries the
current setting.
5-135
:SEARch<x>:SPOint
Sets the search start position or queries the current setting. 5-135
:SEARch<x>:STRace
Sets the search source trace or queries the current setting. 5-135
:SEARch<x>:TRACe<x>?
Queries all settings related to the search conditions of the trace. 5-136
:SEARch<x>:TRACe<x>:CONDition
Sets the condition to be satisfied for the trace or queries the current setting. 5-136
:SEARch<x>:TRACe<x>:HYSTeresis
Sets the hysteresis of the trace or queries the current setting. 5-136
:SEARch<x>:TRACe<x>:LEVel
Sets the threshold level of the trace or queries the current setting. 5-136
:SEARch<x>:TYPE
Sets the search type or queries the current setting. 5-136
:SEARch<x>:WIDTh?
Queries all settings related to the pulse width search. 5-136
:SEARch<x>:WIDTh:MODE
Sets the pulse width determination mode or queries the current setting. 5-136
:SEARch<x>:WIDTh:TIME<x>
Sets the pulse width of the pulse width search or queries the current setting. 5-136
:SEARch<x>:WIDTh:TYPE
Sets the pulse width search type or queries the current setting. 5-136
SNAP Group
:SNAP
Executes the snapshot. 5-137
SSTart Group
:SSTart?
Starts the waveform acquisition with the trigger mode set to single. If the
waveform acquisition stops within the specified time period, 0 is returned at
that point.
5-138
5.1 List of Commands
To Next Page
Loading...
