YOKOGAWA DLM2000 Series - Page 81

5-48
IM 710105-17E
5.1 List of Commands
Command Function Page
:TRIGger{[:ATRigger]|:BTRigger}
:SPI:DATA<x>:SOURce
Sets or queries the data signal for SPI bus signal triggering. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:SPI:MODE
Sets or queries the wiring system (three-wire or four-wire) for SPI bus signal
triggering.
5-264
:TRIGger{[:ATRigger]|:BTRigger}
:TYPE
Sets or queries the trigger type. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART?
Queries all UART signal trigger settings. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:BITorder
Sets or queries the UART signal trigger bit order. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:BRATe
Sets or queries the UART signal trigger bit rate (data transfer rate). 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA?
Queries all UART signal trigger data settings. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:ASCii
Sets the UART bus signal trigger data in ASCII format. 5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:CONDition
Sets or queries the data comparison condition (true or false) for UART signal
triggering.
5-264
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:CSENsitive
Sets or queries whether to distinguish uppercase and lowercase letters in
ASCII data for the UART bus signal trigger.
5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:DBYTe
Sets or queries the number of data bytes for UART signal triggering. 5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:HEXa<x>
Sets the data for UART signal triggering in hexadecimal notation. 5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:PATTern<x>
Sets or queries the data value for UART signal triggering in binary notation. 5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:DATA:PFORmat
Sets or queries the data input format, which is one of the ID and data
conditions, for UART signal triggering.
5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:ERRor?
Queries all UART signal trigger error settings. 5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:ERRor:FRAMing
Sets or queries the UART signal trigger framing error setting. 5-265
:TRIGger{[:ATRigger]|:BTRigger}
:UART:ERRor:PARity
Sets or queries the UART signal trigger parity error setting. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:ERRor:PMODE
Sets or queries the UART signal trigger parity mode setting. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:FORMat
Sets or queries the UART signal trigger format. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:MODE
Sets or queries the UART signal trigger type. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:POLarity
Sets or queries the UART signal trigger polarity. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:SOURce
Sets or queries the source signal for UART signal triggering. 5-266
:TRIGger{[:ATRigger]|:BTRigger}
:UART:SPOint
Sets or queries the UART signal trigger sample point. 5-266
:TRIGger[:ATRigger]:CANFD?
Queries all CAN FD bus signal trigger settings. 5-266
:TRIGger[:ATRigger]:CANFD:BRATe
Sets or queries the CAN FD bus signal trigger bit rate (data transfer rate). 5-266
:TRIGger[:ATRigger]:CANFD:DBRa
te
Sets or queries the CAN FD bus signal trigger data phase bit rate (data
transfer rate).
5-267
:TRIGger[:ATRigger]:CANFD:DSPoi
nt
Sets or queries the CAN FD bus signal trigger data phase sample point. 5-267
:TRIGger[:ATRigger]:CANFD:ID?
Queries all ID and data condition settings for CAN FD bus signal triggering. 5-267
:TRIGger[:ATRigger]:CANFD[:ID]:
DATA:MODE
Sets or queries the data enable/disable condition, which is one of the ID
conditions, for CAN FD bus signal triggering.
5-267
:TRIGger[:ATRigger]:CANFD[:ID]:
IDENtifier?
Queries all identifier settings for the ID conditions for CAN FD bus signal
triggering.
5-267
:TRIGger[:ATRigger]:CANFD[:ID]:
IDENtifier:ID?
Queries all ID settings for the ID conditions for CAN FD bus signal triggering. 5-267
:TRIGger[:ATRigger]:CANFD[:ID]:
IDENtifier:ID:HEXa
Sets the ID value, which is one of the ID conditions, for CAN FD bus signal
triggering in hexadecimal notation.
5-267
:TRIGger[:ATRigger]:CANFD[:ID]:
IDENtifier:ID:MODE
Sets or queries the ID enable/disable condition, which is one of the ID
conditions, for CAN FD bus signal triggering.
5-267