5-20
IM DLM4038-17EN
Command Function Page
RECall Group
:RECall:SETup<x>:EXECute
Recalls setup data from an internal memory area. 5-148
REFerence Group
:REFerence<x>?
Queries all reference waveform settings. 5-149
:REFerence<x>:DISPlay
Sets or queries the display on/off status of a reference waveform. 5-149
:REFerence<x>:LABel?
Queries all label settings of a reference. 5-149
:REFerence<x>:LABel[:DEFine]
Sets or queries a reference waveform label. 5-149
:REFerence<x>:LABel:MODE
Sets or queries the label display on/off status of a reference. 5-149
:REFerence<x>:LOAD
Loads a reference waveform. 5-149
:REFerence<x>:POSition
Sets or queries the vertical position of a reference waveform. 5-149
SEARch Group
:SEARch?
Queries all waveform search settings. 5-150
:SEARch:ABORt
Aborts searching. 5-150
:SEARch:ASCRoll<x>?
Queries all auto scroll settings. 5-150
:SEARch:ASCRoll<x>:JUMP
Moves the center position of a zoom box to the left or right edge of the main
window.
5-150
:SEARch:ASCRoll<x>:SPEed
Sets or queries the auto scroll speed of a zoom box. 5-150
:SEARch:ASCRoll<x>:STARt
Starts auto scrolling. 5-150
:SEARch:ASCRoll<x>:STOP
Stops auto scrolling. 5-150
:SEARch:EDGE?
Queries all edge search settings. 5-150
:SEARch:EDGE:HYSTeresis
Sets or queries the edge search level hysteresis. 5-150
:SEARch:EDGE:LEVel
Sets or queries the edge search level. 5-150
:SEARch:EDGE:SLOPe
Sets or queries the edge search slope. 5-150
:SEARch:EDGE:SOURce
Sets or queries the edge search source waveform. 5-151
:SEARch:EPOint
Sets or queries search end point. 5-151
:SEARch:EXECute
Executes searching. This is an overlap command. 5-151
:SEARch:MARK
Sets or queries the on/off status of detection point marks. 5-151
:SEARch:MAG<x>
Sets or queries the zoom factor of a zoom window. 5-151
:SEARch:POSition<x>
Sets or queries the position of a zoom box. 5-151
:SEARch:PPATtern?
Queries all state or state width search settings. 5-151
:SEARch:PPATtern:{CHANnel<x>|MA
TH<x>}?
Queries all of the settings of a waveform for state or state edge searching. 5-151
:SEARch:PPATtern:{CHANnel<x>|MA
TH<x>}:HYSTeresis
Sets or queries a source waveform hysteresis for state or state width
searching.
5-151
:SEARch:PPATtern:{CHANnel<x>|MA
TH<x>}:LEVel
Sets or queries a source waveform search level for state or state width
searching.
5-151
:SEARch:PPATtern:{CHANnel<x>|MA
TH<x>}:PATTern
Sets or queries a source waveform search pattern for state or state width
searching.
5-152
:SEARch:PPATtern:CLOCk?
Queries all clock channel settings for state or state width searching. 5-152
:SEARch:PPATtern:CLOCk:HYSTeres
is
Sets or queries the clock channel hysteresis for state or state width
searching.
5-152
:SEARch:PPATtern:CLOCk:LEVel
Sets or queries the clock channel search level for state or state width
searching.
5-152
:SEARch:PPATtern:CLOCk:SLOPe
Sets or queries the clock channel slope for state or state width searching. 5-152
:SEARch:PPATtern:CLOCk:SOURce
Sets or queries the clock channel source waveform state or state width
searching.
5-152
:SEARch:PPATtern:LOGic
Sets or queries the state or state width search logic. 5-152
:SEARch:PPATtern:{PODA|PODB|PO
DL}?
Queries all logic settings for state or state width searching. 5-152
:SEARch:PPATtern:{PODA|PODB|POD
L}:HEXa
Sets the logic satisfaction condition for state or state width searching in
hexadecimal notation.
5-152
:SEARch:PPATtern:{PODA|PODB|POD
L}:PATTern
Sets or queries the logic satisfaction condition for state or state width
searching in binary notation.
5-153
:SEARch:PPATtern:POLarity
Sets or queries the state or state width search polarity. 5-153
:SEARch:PPATtern:TIME<x>
Sets or queries the pulse width setting for state or state width searching. 5-153
:SEARch:PPATtern:TYPE
Sets or queries the search type setting for state or state width searching. 5-153
:SEARch:QUALify?
Queries all edge qualified search settings. 5-153
:SEARch:QUALify:CONDition
Sets or queries the edge qualified search condition. 5-153
5.1 List of Commands
To Next Page
Loading...
